32-09-08
ALL ú ú 04 Page 214 ú Sep 28/99
A
757
MAINTENANCE MANUAL
NOSE GEAR NOT COMPRESSED SENSOR TARGET BRACKET - REMOVAL/INSTALLATION
________________________________________________________________________
1. General
_______
A. This procedure contains two tasks. The first task removes the target for the nose gear not compressed sensor. The second task installs the target for the nose gear not compressed sensor.
TASK 32-09-09-004-001
2. Remove the Target Bracket for the Nose Landing Gear Not Compressed Sensor
_________________________________________________________________________
A. References
(1)
AMM 32-00-15/201, Landing Gear Door Locks
(2)
AMM 32-00-20/201, Landing Gear Downlocks
B.
Access
(1)
Location Zones
119/120 Main Equipment Center
711 Nose Landing Gear (NLG)
713/714 Forward NLG Door
715/716 Aft NLG Door
730/740 Main Landing Gear and Doors
(2)
Access Panel
119BL Main Equipment Center
C.
Prepare for the Removal of the Target (Fig. 401)
S 494-002
(1) Make sure the landing gear downlocks are installed on the nose and main landing gear (AMM 32-00-20/201).
S 494-011
WARNING: USE THE PROCEDURE IN AMM 32-00-15/201 TO INSTALL THE DOOR
_______ LOCKS. THE DOORS OPEN AND CLOSE QUICKLY AND CAN CAUSE INJURY TO PERSONS OR DAMAGE TO EQUIPMENT.
(2)
Open the doors for the landing gear and install the door locks (AMM 32-00-15/201).
(3)
Put chocks at the wheels.
S 494-004
32-09-09
ALL ú ú 02 Page 401 ú Sep 28/99
A
757
MAINTENANCE MANUAL
SHOCK STRUT (REF)
SENSOR TARGET
SEE A
UPPER TORSION LINK (REF)
SENSOR TARGET
SENSOR (REF)
SCREW AND NUT
FWD
SENSOR TARGET WITH GEAR FULLY COMPRESSED (TARGET ON LEFT SIDE OF STRUT SHOWN, TARGET ON RIGHT SIDE OF STRUT SIMILAR)
A
SHOCK STRUT (REF)
SENSOR
(REF)
SCREW AND
NUT (2 LOCATIONS)
0.08
INCH
0.10 CLEARANCE SENSOR
(REF) TARGET
FWD UPPER TORSION LINK (REF)
SENSOR TARGET WITH GEAR FULLY EXTENDED
(TARGET ON LEFT SIDE OF STRUT SHOWN,
TARGET ON RIGHT SIDE OF STRUT SIMILAR)
A
Target Installation for the Nose Landing Gear Not Compressed Sensor
Figure 401
32-09-09
ALL ú ú 01 Page 402 ú Dec 20/94
A
757
MAINTENANCE MANUAL
D. Remove the Target Bracket for the Nose Landing Gear Not Compressed Sensor
S 024-005
(1) Remove the two screws on the target bracket.
TASK 32-09-09-404-006
3. Install the Target Bracket for the Nose Landing Gear Not Compressed Sensor
___________________________________________________________________________
A. References
(1)
AMM 06-41-00/201, Fuselage (Major Zones 100 and 200) Access Doors and Panels
(2)
AMM 07-11-02/201, Jacking Airplane Nose
(3)
AMM 32-09-08/201, Nose Gear Not Compressed Sensors
B.
Access
(1)
Location Zones
119/120 Main Equipment Center
711 Nose Landing Gear (NLG)
713/714 Forward NLG Door
715/716 Aft NLG Door
730/740 Main Landing Gear and Doors
中國航空網(wǎng) m.k6050.com 航空翻譯 www.aviation.cn 本文鏈接地址：757 AMM 飛機(jī)維護(hù)手冊(cè) 起落架 CHAPTER 32 - LANDING GEAR 1(71)
