S 034-014

 (7)
Seal the hydraulic fittings and cap the electrical connectors.

 S 034-057

 (8)  
Disconnect the electrical lines from the junction box at each end of the truck beam.

 (9)  
Remove the junction boxes.

 (10)
 Cap the electrical connectors.

 S 014-016
 S 034-017
 

 32-11-17
 ALL  ú ú 03 Page 406 ú May 28/99
 
A

757
MAINTENANCE MANUAL

 S 034-020
 (11)
 Disconnect the clamps and remove the truck shield from the truck beam.

 S 034-021

 (12)
 Disconnect the proximity sensors for the truck tilt.  Hold the sensors out of the way.

 S 014-022

 (13)
 Remove the pin (1) to disconnect the rod end of the truck positioner actuator from the truck beam (View A-A). Hold the actuator out of the way.

 S 844-023

 (14)
 Use a rope or a sling to hold the truck.

 S 014-024

 (15)
 Remove the shock strut lock and slowly lower the truck on a transportation dolly.

 S 844-025

 (16)
 Wind a rope around the fork of the inner cylinder.  Lift the inner cylinder to release the pressure on the pivot pin for the truck.

 S 014-026

 (17)
 Remove the nut (13) with the crowfoot wrench.  Install the thread protector.

 S 014-027

 (18)
 Remove the pin (8) to disconnect the truck assembly from the inner cylinder of the shock strut (View B-B).

 S 584-028

 (19)
 Lift the inner cylinder until it is clear.

 S 024-029

 (20)
 Remove the truck assembly (7) from the area.

 TASK 32-11-17-404-030
 3. Install the Truck Assembly for the Main Landing Gear (Fig. 401)
____________________________________________________
 A. Equipment
 (1)  
Thread Protector Set, MLG - B32011-14

 (2)  
Shock Strut Lock Equipment, MLG - B32028-1

 (3)  
Crowfoot Wrench - F70312-22

 B.
Consumable Materials

 (1)  
C00174 Compound - Corrosion Prevention,
 MIL-C-16173 grade 4

 32-11-17
 ALL  ú ú 04 Page 407 ú Jan 28/00
 
A
757
MAINTENANCE MANUAL

 (2)  
D00633 Grease - BMS 3-33 (Recommended)

 (3)  
D00013 Grease - MIL-G-23827 (Alternative)

 (4)  
D00528 Lubricant - ROYCO 11MS

 C.
Parts

 ~.............................................................................. | MM | | IPC | ................. ............................ | FIG | ITEM | NOMENCLATURE | SUBJECT |FIG | ITEM | ................................................................................ | 401  |  1 | Pin | 32-11-01 | 10 | 200 | | | 2 | Washer | 32-32-15 | 1 | 10 | | | 3 | Antirotation Bolt | 32-11-01 | 10 | 192 | | | 4 | Collar | | | 202 | | | 5 | Washer | | | 193 | | | 6 | Nut | | | 194 | | | 7 | Truck Assembly | | | 150 | | | 8 | Pin | | | 115 | | | 9 | Splined Washer | | | 120 | | | 10 | Bolt | | | 100 | | | 11 | Washer | | | 102 | | | 12 | Nut | | | 103 | | | 13 | Nut | | | 121 | 2......…........…...................................…...........…....….........1
 D. References
 (1)  
AMM 07-11-01/201, Jacking Airplane

 (2)  
AMM 07-11-03/201, Jacking Airplane Axles

 (3)  
AMM 12-21-14/301, Main Gear and Actuating Mechanisms

 (4)  
　
中國航空網(wǎng) m.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：757 AMM 飛機(jī)維護(hù)手冊 起落架 CHAPTER 32 - LANDING GEAR 1(114)