5.
COLLAR PIN

SHOCK A
(2 PLACES) STRUT
10. RIGHT COLLAR BUSHING
A
STEERING CYLINDER ROD END
AFT STEERING COLLAR
6.
O-RING

7.
O-RING

FORWARD 8. RETAINER FWD STEERING BOLT
COLLAR 9. BUSHING
B
Nose Gear Steering Collar Installation Figure 401
EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú

 32-51-06
 ALL  ú ú 01 Page 403 ú Jun 10/88
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A

747-400
MAINTENANCE MANUAL

NUTS
FWD
PULL BOX A-A
RIGID CONDUIT
P37 PANEL
CLAMP
A CLAMP PULL BOX
A
AXLE PENETRATION FITTING
Nose Gear Electrical Installations
Figure 402

EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú

 32-51-06
 ALL  ú ú 01 Page 404 ú Jun 10/88
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A 747-400 MAINTENANCE MANUAL
BEARING HALF
ACTUATOR FLANGE
A
STEP A
A
BEARING HALF
STEP B
FWD
BEARING HALF
ACTUATOR FLANGE
STEP C
A-A
Steering Collar Bearing RemovalFigure 403
EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú

 32-51-06
 ALL  ú ú 01 Page 405 ú Jun 10/88
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
747-400
MAINTENANCE MANUAL

A  A  SHOCK STRUT 
A 
SEE  A  FWD FORWARD STEERING COLLAR  AFT STEERING COLLAR  STEERING CYLINDER ROD END 
A 
AFT STEERING COLLAR 
SEE  B  FORWARD STEERING COLLAR (EXAMPLE) SEALANT 
A-A  B 
Figure 404 Nose Gear Steering Collar Sealant Requirements 

A39234
 EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú

 32-51-06
 ALL  ú ú 01 Page 406 ú Jun 10/92
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A 747-400 MAINTENANCE MANUAL
 (2)  S 344-028Disconnect the cables from the trunnion pivot link drum.
 (3)  S 014-007Do this task: "Torsion Links Removal (Fig. 401)" (AMM 32-21-03/401).
 (4)  S 014-008Loosen the electrical rigid conduit between the runway turnoff light (P37 panel) and the squat switch pull box (Fig. 402). (a) Remove the fasteners attaching the clamps to the brackets. 1) Do not remove the clamps from the conduit (Fig. 402). (b) Loosen the conduit coupling nut at the pull box fitting one to two turns. 1) Do not remove it.
 CAUTION:_______ UNDER NO CONDITIONS SHALL THE BAND CLAMPS AROUND THE SHOCK STRUT BE LOOSENED. CARE MUST BE TAKEN NOT TO MOVE THE BLOCK LUGS ON THESE CLAMPS. REASSEMBLY INSTALLATION AND ALIGNMENT OF PARTS WILL BE DIFFICULT IF THE LUGS ARE MOVED.
 (c) (d)  Remove the nuts holding the bracket to the shock strut.The rigid conduit must be held to the left so that it clears the left steering collar pin (5).
 (5)  S 034-009With the collar positioned between 0 and a 5 degree left turn, remove the left collar pin as follows: (a) Remove the retainer ring (1). (b) Remove the lube insert (3) and discard the O-rings (2). (c) Remove the retainer nut (4) and the retainer bolt (8) and discard the O-ring (7). (d) Remove the bushing (9) and discard the O-ring (6). (e) Remove the collar pin (5).
 (6)  S 034-010Turn the steering collar approximately 45 degrees counterclockwise.
 (7)  S 034-029Remove the right collar pin with the same procedures used for removing the left collar pin.
 (8)  S 024-011Remove the steering collar halves (Fig. 403).
 NOTE:____ The aft collar half can be removed by turning it around the
　
中國航空網 m.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：747-400 AMM 飛機維護手冊 起落架 LANDING GEAR 8(33)