32-51-05
 ALL  ú ú 01 Page 202 ú Jun 10/93
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
747-400
MAINTENANCE MANUAL

 S 012-004
 (6)  If the left-hand cylinder is affected, remove the hand hold (8).
 (a)  Remove the nut (12) from the clamps (10 and 11).
 (b)  Pull the hand hold (8) and the clamps (10 and 11) from the
 actuator.
 S 012-027
 (7)  If the right-hand cylinder is affected, remove the external power
 cable support (13).
 (a)  Remove the nuts (16) from clamps (14 and 15).
 (b)  Remove the clamps (14 and 15) and the external power cable
 support (13) from the actuator.
 S 022-005
 (8)  If the leak is at the aft end of the transfer tube, remove the parts
 as follows:
 (a)  Remove the transfer tube retainer (1) and the backing plate
 (2).

 CAUTION: OBSERVE CARE TO PREVENT ENTRY OF DUST, DIRT OR OTHER
_______ CONTAMINANTS TO SEALING AREAS WHILE TRANSFER TUBE SEALS ARE EXPOSED.
 (b)  
Thoroughly clean the forward and the aft external surfaces of the transfer tube (5) and the adjacent surfaces of the ports.

 (c)  
Slide the transfer tube (5) forward to expose the piston seal set (4) on the aft end of tube.

 (d)  
Remove the seal set.

 S 422-006
 (9)  
Install new seals on the aft end of the transfer tube.

 (a)  
Install a new seal set (4) on the aft end of the transfer tube (5).

 (b)  
Slide the transfer tube (5) aft into the cylinder barrel receptacle and install the retainer (1), the backing plate (2), the washers (6), and the bolts (3).

 (c)  
Tighten the bolts to 65-90 pound-inches torque and lockwire them.

 S 022-007
 (10)
 If the leak is at the forward end of the transfer tube, remove parts as follows:

 (a)  
Remove the lockwire and the sealant from the barrel retaining nut.

 (b)  
Remove the transfer tube retainer (1) and the backing plate (2).

 EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú

 32-51-05
 ALL  ú ú 01 Page 203 ú Jun 10/93
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A

747-400
MAINTENANCE MANUAL

SEE A
B BA
FWD
A
1.
 TRANSFER TUBE TRUNNION RETAINER (2 PLACES)

2.
 BACKING PLATE

4. PISTON SEAL SET (2 BACKUP RINGS, 1 ELASTOMER)
6. WASHER (4 PLACES) 5. TRANSFER TUBE
4. PISTON SEAL SET (2 BACKUP RINGS,
3. BOLT  1 ELASTOMER) (4 PLACES)
7. KEY
BARREL
RETAINING
NUT

BARREL
A
Nose Gear Steering Cylinder Transfer Tube O-Ring Seal Replacement Figure 201 (Sheet 1)
EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú

 32-51-05
 ALL  ú ú 02 Page 204 ú Feb 10/89
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
747-400
MAINTENANCE MANUAL

HAND HOLD DOES NOT TOUCH THE TRANSFER TUBE.
INSTALL EXTERNAL POWER CABLE SUPPORT WITH GOOD CLEARANCE AROUND TRANSFER TUBE BOND AT MATING SURFACE
Nose Gear Steering Cylinder Transfer Tube O-Ring Seal Replacement
Figure 201 (Sheet 2)

EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú

 32-51-05
 ALL  ú ú 03 Page 205 ú Feb 10/89
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
747-400
MAINTENANCE MANUAL

 CAUTION: OBSERVE CARE TO PREVENT ENTRY OF DUST, DIRT OR OTHER
_______ CONTAMINANTS TO SEALING AREAS WHILE TRANSFER TUBE SEALS ARE EXPOSED.
 (c)  
Thoroughly clean the forward and the aft external surfaces of the transfer tube (5) and the adjacent surfaces of the ports.
　
中國航空網 m.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：747-400 AMM 飛機維護手冊 起落架 LANDING GEAR 8(24)