CAUTION: THE TWO ENDS OF THE VALVE ASSEMBLY MUST BE KEPT AT THE SAME
_______ LEVEL DURING VALVE REMOVAL. UNEVEN REMOVAL OF THE LEFT AND RIGHT RETAINER NUTS CAN CAUSE VALVE ASSEMBLY TUBE DAMAGE.
(7) Remove the valve retainer nuts evenly, at the two ends of the valve, using a torque wrench adapter.
S 024-012
CAUTION: DISCONNECTING THE METERING VALVE FROM THE STEERING CYLINDERS
_______ WILL EXPOSE OPEN HYDRAULIC PASSAGES. CAREFULLY REMOVE ALL CONTAMINATION, SUCH AS SAND AND DIRT, FROM THE AREA AROUND AND IN THE TRUNNIONS BEFORE TO EXPOSING THE OPEN PORTS.
(8)
Remove the valve.
(a)
Install the valve input arm on the valve.
S 214-013
(9)
Make sure the rubber seal or the metal ring cannot be seen out of the trunnion bearings.
(a)
If the seal or ring is out, replace the bearing (AMM 32-51-12/401).
(b)
Apply penetrating oil before removing the bearing to reduce possible damage to the bearing or the support plate.
EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú
32-51-04
ALL ú ú 01 Page 405 ú Jun 10/93
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
747-400 MAINTENANCE MANUAL
TASK 32-51-04-404-014
3. Steering Metering Valve Installation____________________________________
A. Special Tools and Equipment
(1) G12001 - Rigging Pins Rigging Pin NS-5 0.311 (+0.000/-0.002)-inch diameter, 4.00-inch length Rigging Pin NS-6 - 0.188 (+0.000/-0.002)-inch diameter, 2.50-inch length
NOTE: Rigging pin is part of G12001 tool kit
____
(2)
3MIT65B01519-1 - Torque Wrench Adapter
B.
Standard Tools and Equipment
(1)
Sealant Gun - Semco type or equivalent
(2)
Wooden or plastic sealant spatula
(3)
Small paint brush
C.
Consumable Materials
(1)
D00153 Hydraulic Fluid, Fire-Resistant - BMS 3-11
(2)
B00185 Isopropyl alcohol - TT-I-735
(3)
A00303 Dow Corning Silicone sealant or equivalent - RTV174
(4)
C00048 Dow Corning primer or equivalent - RTV1200
(5)
C00174 Corrosion Preventive Compound - MIL-C-16173, Grade 3
(6)
G00034 Clean, Lint free cloth
D. Parts ~.............................................................................. | AMM | | AIPC | ................. ............................ | FIG | ITEM | NOMENCLATURE | SUBJECT | FIG | ITEM | ................................................................................ | 401 | 1 | Metering Valve Attach Bolt | 32-51-00 | 01 | 110 | | | 2 | Metering Valve Attach Bolt | | | 105 | | | 3 | Washer | | | 115 | | | 4 | Cover Retainer Bolt | 32-51-60 | 01 | 5 | | | 5 | Nut | | | 120 | | | 6 | Metering Valve Assembly | 32-51-00 | 01 | 125 | 2......…........…...................................…..........….......….......1
E. References
(1)
AMM 29-11-00/201, Main Hydraulic Supply System
(2)
AMM 32-00-30/201, Landing Gear Door Locks
(3)
AMM 32-21-03/201, Nose Gear Torsion Links
EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú
32-51-04
ALL ú ú 03 Page 406 ú Feb 15/98
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
747-400
MAINTENANCE MANUAL
(4)
AMM 32-51-12/401, Nose Gear Steering Actuator
F.
Access
(1)
Location Zone
715 Nose Landing Gear
中國航空網 m.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：747-400 AMM 飛機維護手冊 起落架 LANDING GEAR 8(17)
