S 834-029
EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú
32-51-01
ALL ú ú 01 Page 405 ú Oct 18/99
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
747-400 MAINTENANCE MANUAL
S 434-031
(4) Tighten the clamp screw of the tiller handle to 27-33 pound-inches
(3.1 - 3.7 Nm) torque.
EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú
32-51-01
ALL ú ú 01 Page 406 ú Oct 18/99
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
747-400 MAINTENANCE MANUAL
RUDDER PEDAL STEERING MECHANISM - REMOVAL/INSTALLATION
______________________________________________________
1. General_______
A. This procedure has two tasks:
(1)
The removal of the steering mechanism of the rudder pedal
(2)
The installation of the steering mechanism of the rudder pedal.
B.
The steering mechanism of the rudder pedal is found on the ceiling in the forward passenger cabin.
TASK 32-51-02-004-001
2. Rudder Pedal Steering Mechanism Removal_______________________________________
A. Special Tools and Equipment
(1) G12001 - Rigging pins - 0.308 to 0.311 inch diameter ~.................................. | Pin No. | Length (inches) | .................................... | NS-1 | 4.00 | .................................... | NS-2 | 4.00 | .................................... | NS-4 | 2.50 | 2.............…....................1
NOTE: Rigging pin is part of G12001 tool kit.
____
B. References
(1)
AMM 09-11-00/201, Towing
(2)
AMM 24-22-00/201, Manual Control
(3)
AMM 32-00-30/201, Landing Gear Door Locks
(4)
AMM 32-51-00/501, Nose Wheel Steering System
(5)
AMM 32-51-07/401, Nose Gear Rudder Pedal Steering Interconnect Actuator
(6)
IPC 32-51-61 Fig. 1, IPC 32-51-63 Fig. 1
C.
Access
(1)
Location Zone
211 Forward Passenger Cabin, LH
D.
Prepare for the Removal
S 864-002
(1) Make sure that you install the ground locks in the landing gear (AMM 09-11-00/201).
EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú
32-51-02
ALL ú ú 01 Page 401 ú Oct 18/01
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
747-400 MAINTENANCE MANUAL
S 494-003
WARNING: REFER TO AMM 32-00-30/201 FOR THE LOCK INSTALLATION PROCEDURE.
_______ THE FAST MOVEMENT OF THE DOORS CAN CAUSE INJURY TO PERSONS OR DAMAGE TO EQUIPMENT IF THE LOCKS ARE NOT CORRECTLY INSTALLED.
(2)
Install the door lock of the nose gear.
S 864-004
(3)
Make sure that you remove the electrical power (AMM 24-22-00/201).
S 864-005
(4)
Open these circuit breakers and attach DO-NOT-CLOSE tags:
(a)
P7 Overhead Circuit Breaker Panel
1) 7G23 BODY GR STRG ARM AC
2) 7G24 BODY GR STRG ARM DC
3) 7G25 NOSE GR STRG PRI
4) 7G26 NOSE GR STRG ALTN
S 014-006
(5)
Get access to the steering cables (NWS1A, NWS1B).
(a)
Remove the left forward ceiling panel in the passenger compartment in front of the No. 1 door.
E.
Remove the Rudder Pedal Steering Mechanism (Fig. 401)
S 034-007
(1) Decrease the cable tension at the turnbuckles.
NOTE: This step will decrease the tension equally in each steering
____
cable.
S 034-008
(2)
Disconnect the steering rod from the steering crank.
S 494-009
(3) 中國航空網 m.k6050.com 航空翻譯 www.aviation.cn 本文鏈接地址：747-400 AMM 飛機維護手冊 起落架 LANDING GEAR 8(10)
