(f)  
Drain the bottle and let it dry in the air in a laminar flowbench of a clean room.

 NOTE: If a laminar flow bench is not available, the bottle
____ can be turned with the bottom up and put in a clean dry room. All persons must stay away from the room until the bottle is dry and sealed with a cap.
 (g)  
When the bottle is dry, install the screw cap.

 (h)  
Put the bottle in a new polyethylene bag.

 (i)  
Seal the bag with a knot or some tape.

 (j)  
Identify the bag.

 S 016-006
 (3)  
Open the fairing doors on the trailing edge of the strut (AMM 54-62-00/201).

 S 876-015

 (4)  
Get a hydraulic fluid sample (Fig. 601):

 (a)  
Put the container below the hydraulic sample valve.

 EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú
 29-00-00
 ALL  ú ú 01 Page 605 ú Jun 18/01
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
747-400
MAINTENANCE MANUAL

 WARNING:_______DO NOT LET THE HYDRAULIC FLUID STAY ON YOUR SKIN. YOU CAN ABSORB POISONOUS MATERIALS FROM THE FLUID THROUGH YOUR SKIN.
 CAUTION: IMMEDIATELY CLEAN ALL THE HYDRAULIC FLUID THAT FALLS ON
_______ THE AIRPLANE PARTS. THE FLUID CAN CAUSE DAMAGE TO THE PAINT AND CORROSION TO SOME PARTS.
 (b)  
Open the sample valve sufficiently to permit a smooth flow of fluid with no bubbles or spray.

 (c)  
Drain a minimum of 1 pint of fluid through the valve before you get a sample.

 (d)  
Remove the cap from the polyethylene bottle.

 (e)  
Put the bottle in the fluid flow.
 1) Do not let the bottle touch the sample valve.

 (f)  
When the bottle is almost full, remove it from the flow.

 NOTE: This will make sure that unwanted materials do not
____ loosen and cause a change in the sample when you close the valve.
 (g)  
Put the cap on the bottle.

 (h)  
Remove the cap from the glass bottle.

 (i)  
Put the bottle in the fluid flow.
 1) Do not let the bottle touch the sample valve.

 (j)  
When the bottle is almost full, remove it from the flow.

 NOTE: This will make sure that unwanted materials do not
____ loosen and cause a change in the sample when you close the valve.
 (k)  
Put the cap on the bottle.

 (l)  
Close the sample valve.
 1) Install a lockwire on the sample valve.

 (m)  
Identify the sample bottles with a label as follows:
 1) The airplane model
 2) The airplane number
 3) The hydraulic system number
 4) The date
 5) The fluid location.

 S 416-013
 (5)  
Close the fairing doors on the trailing edge of the strut (AMM 54-62-00/201).

 (6)  
Do this task: "Hydraulic Reservoir Servicing" (AMM 12-12-01/301).

 S 616-014
 EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú
 29-00-00
 ALL  ú ú 01 Page 606 ú Jun 18/01
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
747-400 FAULT ISOLATION/MAINT MANUAL
MAIN HYDRAULIC SUPPLY SYSTEM
COMPONENT  FIG. 102 SHT  QTY  ACCESS/AREA  REFERENCE 
DRIVE ASSEMBLY - SYS 1 GOVERNOR UNIT AND OIL PUMP  7  1  454A TRAILING EDGE FAIRING DOORS  29-11-10 
ASSEMBLY - SYS 4 GOVERNOR UNIT AND OIL PUMP DRIVE  7  1  484A TRAILING EDGE FAIRING DOORS  29-11-10 
CARD - HYD INTERFACE MODULE (HYDIM) CIRCUIT 12  M7603 ELEC SYSTEMS CARD FILE  29-11-42 
SYS 1, YMLA20  1 
SYS 2, YMLA21  1 
SYS 3, YMLA22  1 
SYS 4, YMLA23  1 
CIRCUIT BREAKERS  1  FLT COMPT, P6 
FIRE EXTINGUISHER ENG 1 & 3 B, C211 1  6H1  * 
FIRE EXTINGUISHER ENG 1 & 3 A, C212 1  6H2  * 
FIRE EXTINGUISHER ENG 2 & 4 B, C213 1  6H3  * 
　
中國航空網(wǎng) m.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：747-400 AMM 飛機維護手冊 液壓 HYDRAULIC 1(9)