E.
Procedure

 S 012-044
 (1)  
Open the thrust reverser half on the right side of the engine (AMM 78-31-00/201).

 (2)  
Remove the EDP (AMM 29-11-05/401).

 (3)  
Disconnect the drain line for the pump pad.

 (4)  
Install the pump pad plug.

 S 022-013
 S 032-014
 S 432-015
 EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú

 29-11-05
 ALL  ú ú 01 Page 205 ú Oct 18/01
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
747-400 MAINTENANCE MANUAL
 S 432-016
 (5)  
Install the plugs, with packings, on the inlet hose, the outlet hose, and the case drain hose.

 S 032-017

 (6)  
Remove the quillshaft from the EDP.

 S 872-018

 (7)  
Fully drain the EDP.

 S 432-045

 (8)  
Install the plug and seal assembly:

 (a)  
If the plug and seal assembly is not assembled, assemble the plug and seal assembly: 1) Lubricate the packings with engine oil. 2) Install the small packing in the groove adjacent to the

 head of the gearshaft bolt. 3) Install the large packing in the groove adjacent to the flange at the end of the gearbox plug. 4) Install the gearbox bolt into the gearbox plug at a sufficient depth to start the nut on the bolt.

 (b)  
Install the plug and seal assembly on the end of the gearshaft.

 NOTE: The bolt head must engage the groove behind the
____ drive shaft splines before the plug engages the gear shaft splines.
 (c)  
After the head of the bolt engages the gear shaft groove, push the plug fully into the gear shaft. 1) Make sure the plug splines engage with the gear shaft

 splines.

 (d)  
Remove the nut and install the washer.

 (e)  
Install the nut on the bolt. 1) Tighten the nut to 36-40 pound-inches (4.1-4.5 N.m).

 S 422-021
 (9)  
Install the deactivated EDP on the pump pad (AMM 29-11-05/401).

 (a)  
Use a 69B91091-2 gasket that is optional to the initial 69B91091-1 gasket.

 NOTE:____Engine oil can possibly get into the EDP. You must examine the EDP before you operate it.
 S 032-065
 (10)
 Install caps on the inlet, outlet, and case drain ports of the EDP.

 S 862-022

 (11)
 Run the engine at idle (AMM 71-00-00/501) and examine the installation for oil leakage.

 EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú

 29-11-05
 ALL  ú ú 01 Page 206 ú Oct 18/01
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
747-400
MAINTENANCE MANUAL

 S 862-023
 (12)
 Pressurize the hydraulic system and examine for leakage (AMM 29-11-00/201).

 S 862-040

 (13)
 Release the pressure in the hydraulic system, if it is not necessary (AMM 29-11-00/201).

 S 412-041

 (14)
 Close the thrust reverser on the right side of the engine (AMM 78-31-00/201).

 TASK 29-11-05-402-026
 4. Engine-Driven Pump (EDP) Dispatch Equipment Removal (Fig. 201)
___________________________________________________
 A. References
 (1)
AMM 24-22-00/201, Manual Control

 (2)
AMM 29-11-00/201, Hydraulic Power

 (3)
AMM 29-11-05/401, Engine-Driven Pump

 (4)
AMM 36-00-00/201, Pneumatic System

 (5)
AMM 78-31-00/201, Thrust Reverser System

 B.
Access

 (1)  
Location Zone 412 Engine 1 - Gearbox Forward Face 5:00 o'clock 422 Engine 2 - Gearbox Forward Face 5:00 o'clock 432 Engine 3 - Gearbox Forward Face 5:00 o'clock 442 Engine 4 - Gearbox Forward Face 5:00 o'clock

 (2)  
Access Panel
 416 Right Thrust Reverser Half - Engine 1
 426 Right Thrust Reverser Half - Engine 2
 436 Right Thrust Reverser Half - Engine 3
 446 Right Thrust Reverser Half - Engine 4
　
中國航空網(wǎng) m.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：747-400 AMM 飛機(jī)維護(hù)手冊(cè) 液壓 HYDRAULIC 1(100)