EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú

 29-11-00
 ALL  ú ú 01 Page 602 ú Oct 18/01
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
747-400 MAINTENANCE MANUAL
 S 486-644
 (5)  
If you use a hydraulic service cart for the pressure source, connect the hydraulic service cart (AMM 29-11-00/201):

 (a)  
Connect the cart to the ground-service disconnect on the pressure module of the No. 1 and No. 4 hydraulic systems.

 (b)  
Install a flowmeter in the cart pressure line which connects to the No. 1 hydraulic system.

 (c)  
Connect the return line on the hydraulic service cart to the No. 1 and No. 4 return modules (AMM 29-11-00/201).

 S 486-645
 (6)  
If you use the system demand pump for the pressure source, release the pressure in hydraulic system No. 1 (AMM 29-11-00/201).

 (a)  
Install a flowmeter in the pressure line on the No. 1 demand pump between the pump and the pressure module.

 (b)  
Make sure there is a minimum of 2000 pounds (900 kg) of fuel in the No. 1 and No. 4 main fuel tanks.

 NOTE: The fuel weight values are calculated with a fuel
____ density of 6.7 pounds per gallon.
 S 866-646
 (7)  Make sure the control column, the control wheel, and the rudder pedals are in the neutral position.
 NOTE: It is not necessary for the flaps and the stabilizer to be in
____
 the neutral position.

 S 866-647
 (8)  
Put the A/P ENGAGE switches (L, C, and R) on the control panel for the AFCS mode in the off position.

 S 866-648

 (9)  
Put the system No. 1 WING FLT CONTROL SHUTOFF switch on the P461 overhead maintenance panel in the ON position.

 S 866-649

 (10)
 Put the system No. 1 TAIL FLT CONTROL SHUTOFF switch on the P461 overhead maintenance panel in the ON position.

 S 866-650

 (11)
 Make sure that the selector handle for the landing gear on the P2 first officer's panel is in the OFF position.

 E.
Hydraulic System No. 1 - Gross Internal Leakage Check

 (1)  
Pressurize hydraulic systems No. 1 and No. 4 to 3000 psig.

 S 866-651
 EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú

 29-11-00
 ALL  ú ú 01 Page 603 ú Jun 18/01
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
747-400 MAINTENANCE MANUAL
 S 866-652
 WARNING: MAKE SURE THAT PERSONS AND EQUIPMENT ARE CLEAR OF THE LE AND TE
_______ FLAPS AND FLAP DRIVE MECHANISMS BEFORE YOU MOVE THE FLAP CONTROL LEVER. WITH HYDRAULIC POWER REMOVED, THE FLAPS WILL MOVE AUTOMATICALLY BY ELECTRICAL POWER WHEN YOU MOVE THE FLAP CONTROL LEVER.
 (2)  
Operate the flight controls through four or five cycles.

 S 866-653

 (3)  
Operate the inboard flaps through 3 full cycles.

 S 866-654

 (4)  
Keep the flight controls in the neutral position.

 S 976-655

 (5)  
Let the flow become stable for 3 minutes and make a record of this flow.

 NOTE: This flow is the gross internal leakage for the No. 1
____
 hydraulic system.

 S 796-656
 (6)  If the gross internal leakage of the No. 1 hydraulic system is more than 5 GPM, do the Hydraulic System No. 1 Full Internal Leakage Check procedure.
 NOTE: This procedure will find the component which has too much
____
 leakage.

 F. Put the Airplane Back to Its Usual Condition
 S 866-657
 (1)  
Release the pressure in hydraulic systems No. 1 and 4
 (AMM 29-11-00/201).

 S 086-658

 (2)  
If you used the system demand pump for a pressure source, remove the flowmeter:

 (a)  
Remove the flowmeter from the pressure line of the demand pump.

 (b)  
Connect the pressure line for the demand pump to the pump port for the demand pump.

 (c)  
Put the system HYD PUMPS DEMAND switch in the ON position (P5 Overhead Panel).
　
中國航空網 m.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：747-400 AMM 飛機維護手冊 液壓 HYDRAULIC 1(45)