(b)  Disconnect the electrical connector (1), for the applicable
 system, from the position switch on the shutoff valve actuator:
 1) DM647B for system 1
 2) DM874B for system 4.
 (c)  Remove the screws (16).
 (d)  Remove the bolts (5 and 8), the washers (6), the spacer (9),
 and the nuts (7).
 (e)  Remove the two clamps (4) from the wire harness.
 (f)  Disconnect the pressurization hose (3) for the hydraulic
 reservoir from the pneumatic duct.
 1) Install caps on the hose and the port to prevent
 contamination.
 (g)  Remove the clamp (13) that attaches the turbine drive (2) to
 the pneumatic duct.
 (h)  Remove the nuts (20), washers (21), and the bolts (22) to
 disconnect the support rods (17) from the aft flange of the
 turbine drive (2).
 NOTE: Make sure you hold the turbine drive during the____
 removal to prevent damage to the drive unit or the
 airplane structure.
 1) Do not remove the support rods from the mounting bracket
 (10).
 (i)  Remove the bolt (12) and the washer (11) from the left side
 support strut of the mounting bracket (10).
 (j)  Remove the bolts (18) and the washers (19) that attach the
 mounting bracket to the strut bulkhead.
 (k)  Remove the mounting bracket (10).

 CAUTION:_______BE CAREFUL WITH THE TURBINE DRIVE DURING THE REMOVAL. A ROUGH MOVEMENT OF THE TURBINE DRIVE CAN CAUSE OIL TO FLOW AROUND THE TURBINE SHAFT SEAL AND COLLECT IN THE EXHAUST SCROLL.
 (l)  
Remove the bolt (26) and the bushing (25) from the forward left side mounting flange.

 (m)  
Remove the bolt (24) from the forward right side mounting flange.

 (n)  
Carefully lift the turbine drive (2) around the pneumatic duct and remove it through the right side of the strut.

 EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú

 29-11-08
 ALL  ú ú 01 Page 409 ú Oct 10/95
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
747-400
MAINTENANCE MANUAL

 (o)  Remove the seal from the flange of the turbine drive exhaust and remove the turbine exhaust cascade (15) from the turbine drive.
 S 684-120
 CAUTION: TO PREVENT OIL FROM ENTERING INLET AND CONTAMINATING CARBON
_______ SEAL, OIL MUST BE DRAINED AFTER TURBINE DRIVE IS REMOVED.
 (10)
 Drain oil from oil sump

 S 214-037

 (11)
 Examine the condition of the screen in the air inlet of the pneumatic duct.

 (a)  
Clean or replace the screen if it is necessary (AMM 36-11-24/401).

 S 494-038
 (12) Install a cover on the pneumatic duct to prevent contamination.
 TASK 29-11-08-404-104
 4. Air-Driven Pump Turbine Drive Installation for System 1 Without Auxiliary
_________________________________________________________________________ Hydraulic Pump (Fig 401)
______________
 A. Special Tools and Equipment
 (1)  
ME60B00158 Air-Driven Hydraulic Pump Muffler

 B.
Consumable Materials

 (1)  
D00013 Grease, MIL-G-23827

 (2)  
D00071 Oil - Aircraft Turbine Engine Lubricating, MIL-L-7808 (optional to MIL-L-23699)

 (3)  
D00068 Oil - Aircraft Turbine Engine Lubricating, MIL-L-23699 (optional to MIL-L-7808)

 (4)  
D00153 Fluid - Hydraulic, Fire-Resistant BMS 3-11

 (5)  
G00095 Detector - Leak, Leak Tek (160X)

 C.
References

 (1)  
AMM 12-12-01/301, Hydraulic Systems

 (2)  
AMM 12-13-09/301, Air-Driven Pump Turbine Drive

 (3)  
AMM 24-22-00/201, Manual Control

 (4)  
AMM 29-11-17/401, Air-Driven Pump

 (5)  
AMM 36-00-00/201, Pneumatic System

 (6)  
AMM 54-62-00/201, Nacelle Strut Access Panels

 D.
Access

 (1)  
Location Zone
 454 System 1 - Strut Aft Fairing

 (2)  
Access Panel 454A Trailing Edge Fairing Doors - System 1
　
中國航空網 m.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：747-400 AMM 飛機維護手冊 液壓 HYDRAULIC 1(118)