(a)
The mounting flange of the motor/impeller unit and mating surfaces on the housing.
(b)
The bonding clip (9 or 10) and motor/impeller unit (1).
(c)
The bonding jumper (8) and the faying surface of the bonding clip (9 or 10) if the bonding jumper electrical connection is to be reworked (View A-A).
EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú
28-22-03
ALL ú ú 01 Page 408 ú Oct 18/00
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
747-400
MAINTENANCE MANUAL
(d) Apply Alodine 600 to bare metal areas to prevent corrosion and degradation of the bond.
(2) S 434-021Install the new packings (2, 3, and 4), lubricated with petrolatum grease, into the grooves on the motor/impeller unit (1).
(3) S 434-022Install the new packing, lubricated with petrolatum, on the drain plug and install plug in the motor/impeller unit (1).
(4) S 434-045Install the drain plug in the motor/impeller unit (1).
(5) S 434-046Install lockwire on the drain plug (9).
(6) S 614-023Put 1/2 to 1 pint of fuel into two smaller slots in the top side of the motor/impeller unit (1).
(7) S 614-047Turn the impeller to help the internal parts of the boost pump get wet.
S 424-048
CAUTION: BE CAREFUL WHEN YOU INSTALL OR TURN THE MOTOR/IMPELLER UNIT IN
_______ THE HOUSING. IF YOU ARE NOT CAREFUL, DAMAGE TO THE PACKING COULD OCCUR.
(8)
Put the motor/impeller unit (1) in the housing.
S 824-054
(9)
Turn the motor/impeller unit (1) until the index hole aligns with the index pin in the housing.
S 434-025
(10)
Install the bonding clip (9) on the motor/impeller unit (1), with two screws (5) (View B). For bonding clip (10), use three screws (5).
NOTE: Do not tighten the screws (5) at this time.
____
S 434-026
(11) Install the remaining screws (5) and washers (6).
EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú
28-22-03
ALL ú ú 01 Page 409 ú Oct 15/98
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
747-400 MAINTENANCE MANUAL
S 434-055
(12)
Tighten all the screws (5) to 17-19 pound-inches.
S 034-149
(13)
Install the lockwire on the socket head screws (5) (View B).
S 034-151
(14)
If the bonding jumper (8) electrical bond to the bonding clip (9, or 10) was reworked, do these steps:
(a)
Install the bonding jumper (8), washers (12), bolt (11) and nut (13) to the bonding clip (9 or 10) (SWPM 20-20-00).
S 374-150
(15)
Apply these finishes to any cleaned areas of the bonding clip (9 or 10) that are not covered by the jumper terminal:
(a)
Alodine 600 (AMM 51-21-04/701)
(b)
BMS 10-20 Type II primer (AMM 28-11-00/801).
S 434-028
(16) Connect the electrical connector to the motor/impeller unit (1).
NOTE: Refer to this table for the equipment numbers.
____
~................................................................. | | Equipment Number | | Location ............................ | | Motor | Connector | ................................................................... | No. 1 Main Tank - Fwd | M28 | DM28 | | No. 1 Main Tank - Aft | M22 | DM22 | | No. 2 Main Tank - Fwd | M29 | DM29 | | No. 2 Main Tank - Aft | M23 | DM23 | | No. 3 Main Tank - Fwd | M26 | DM26 | | No. 3 Main Tank - Aft | M31 | DM31 | | No. 4 Main Tank - Fwd | M27 | DM27 | | No. 4 Main Tank - Aft | M32 | DM32 | 2......................................…...........…..............1
EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú
28-22-03
ALL ú ú 01 Page 410 ú Jun 18/01
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
中國航空網(wǎng) m.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：747-400 AMM 飛機(jī)維護(hù)手冊(cè) 燃油 FUEL 2(115)
