28-22-03
 ALL  ú ú 01 Page 405 ú Jun 18/01
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A

747-400
MAINTENANCE MANUAL

OUTBOARD MAIN BOOST PUMPS SEE A  BOOST PUMPS INBOARD MAIN SEE A  OUTBOARD MAIN BOOST PUMPS SEE A 
BOOST PUMPS INBOARD MAIN SEE A 
MOUNTING PAD (REF) SPAR OR DRY BAY 
UNIT 1. MOTOR/IMPELLER 
SEE  B 
INDEX PIN  4. PACKING 3. PACKING  2. PACKING  CONNECTOR ELECTRICAL PUMP 

INBOARD AND OUTBOARD MAIN BOOST PUMPS A
NOTE:BOOST PUMP INSTALLED ON THE SPAR SHOWN; BOOST PUMP INSTALLED IN THE DRY BAY IS ALMOST THE SAME. FACE MOUNTED ELECTRICAL CONNECTOR SHOWN.
Main Tank Boost Pump Motor/Impeller Unit Installation Figure 401 (Sheet 1)
EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú

 28-22-03
 ALL  ú ú 01 Page 406 ú Oct 15/98
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
747-400
MAINTENANCE MANUAL

7. LOCKWIRE (2 LOCATIONS)
5.
 SCREW

6.
 WASHER STRUCTURE

(QTY 2)
(3 LOCATIONS) MOUNTING BOLTS (8 LOCATIONS)
5. SCREW  (AMM 28-22-12/401) (2 LOCATIONS) DO NOT REMOVE
INDEX PIN HOLE
A
ELECTRICAL BOND SURFACE
1 BOOST PUMP
9. BONDING  A  5. SCREW 
CLIP  8. BONDING JUMPER  11. BOLT 
8. BONDING

MAIN 1 AND 4 FORWARD AND AFT BOOST PUMPS
JUMPER
AND MAIN 2 AND 3 FORWARD BOOST PUMPS B
ELECTRICAL
5.
 SCREW

BOND
6.
 WASHER

12. WASHER SURFACE
(QTY 2) (2 LOCATIONS) 1 13. NUT
BONDING CLIP
MOUNTING BOLT (DO NOT REMOVE)
BONDING JUMPER
INDEX
PIN HOLE  A-A
ELECTRICAL5. SCREW
A
BOND SURFACE
(3 LOCATIONS) 1
8. BONDING
A
JUMPER
10. BONDING CLIP
MAIN 2 AND 3 AFT BOOST PUMPS B
1
PREPARE THE FAYING SURFACE OF THE BONDING CLIP AND THE MATING SURFACE OF THE MOTOR/IMPELLER UNIT FOR AN ELECTRICAL SURFACE BOND (SWPM 20-20-00).
Main Tank Boost Pump Motor/Impeller Unit Installation Figure 401 (Sheet 2)
H46541
 EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú

 28-22-03
 ALL  ú ú 01 Page 407 ú Oct 15/98
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
747-400
MAINTENANCE MANUAL

 C. Parts
 ~.............................................................................. | MM | | IPC | ................. ............................ | FIG | ITEM | NOMENCLATURE | SUBJECT | FIG | ITEM | ................................................................................ | 401 | 1 | Motor/Impeller Unit | 28-22-03 | 05 | 760 | | | 2 | Packing | | | 763 | | | 3 | Packing | | | 762 | | | 4 | Packing | | | 761 | | | 5 | Screw | | | 760A | | | 6 | Washer | | | 760B | 2......…........…...................................…..........….....….........1
 D. References
 (1)  
AMM 20-11-14/701, Metal Surfaces

 (2)  
AMM 28-11-00/801, Fuel Tank Repair

 (3)  
AMM 51-21-04/701, Alodine Coating

 (4)  
SWPM 20-20-00, Electrical Bond and Ground

 (5)  
SSM 28-22-03, 28-22-04

 (6)  
WDM 28-22-31, WDM 28-22-32, WDM 28-22-33, WDM 28-22-34

 E.
Access

 (1)  
Location Zones 541 Inbd Main Tank (Part), Front Spar to Mid Spar, Left 544 Inbd Main Tank (Part), Mid Spar to Rear Spar, Left 545 Inbd Main Tank (Part), Mid Spar to Rear Spar, Left 641 Inbd Main Tank (Part), Front Spar to Mid Spar, Right 644 Inbd Main Tank (Part), Mid Spar to Rear Spar, Right 645 Inbd Main Tank (Part), Mid Spar to Rear Spar, Right

 (2)  
Access Panels
 545CB Boost Pump Access Door
 545DB Boost Pump Access Door
 645CB Boost Pump Access Door
 645DB Boost Pump Access Door

 F.
Install the Motor/Impeller Unit for the Main Tank Boost Pumps

 S 164-020
 (1)  
Prepare these faying surfaces for an electrical surface bond (SWPM 20-20-00).
　
中國航空網 m.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：747-400 AMM 飛機維護手冊 燃油 FUEL 2(114)