21-51-12
ALL ú ú 01 Page 803 ú Oct 18/00
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
747-400
MAINTENANCE MANUAL
S 348-015
(6) Impregnate each cloth patch with BMS 5-126, and place between two pieces of PVA parting film.
NOTE: Weight of the adhesive must be equal the weight of the
____ dry fiberglass cloth to make the cloth absorb it.
C. Place the Repair Patch
S 348-009
(1)
Apply a layer of BMS 5-126 adhesive mixture, prepared with
manufacturers instructions, on the repair area.
S 348-028
(2)
Remove parting film from one side of the smallest ply of the patch and put its exposed face against the repair area.
S 348-010
(3)
Use a squeegee to remove wrinkles and entrapped air on the parting film that has covers on the patch.
NOTE:____Do not remove the adhesive with too much pressure. This can cause the adhesive patch to fail because there is not enough adhesive.
S 348-011
(4)
Put the next larger size ply of the absorbed patch on the ply. Make sure there is a minimum of 0.80 inch (2.0 cm) overlap all around.
S 348-012
(5)
Make sure you do the same for the other patches as shown in the steps above.
NOTE: If possible, use a complete wrap around ram air duct for
____
the third ply.
S 348-020
(6)
After placing the last ply, cover the entire lay-up with a pice of parting film extending about 0.80 inch (2.0 cm) over the edges of the patch.
S 348-029
(7)
Sweep excess adhesive to the edges of the parting film, fairing the edges of the patch to the contour of the repair surface. Make sure all loose threads are embedded in the resin.
EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú
21-51-12
ALL ú ú 01 Page 804 ú Jun 18/00
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
747-400 MAINTENANCE MANUAL
S 348-030
(8) Wipe off any excess adhesive that has been pushed out at the edges of the parting film.
D. Cure the patch.
S 348-031
(1) Cure the patch. The required curing time for a BMS 5-126 adhesive mixture is about 12 hours at 70 deg F (21 deg C) or 1 hour at 130 deg F (55 deg C).
NOTE: A cured patch is hard and resounds when tapped lightly with a
____
coin or other light metallic object.
S 348-033
(2)
Remove parting film from the patch after curing.
S 218-035
(3)
The patch should be free from pits, blisters, starved areas and extra resin deposits.
EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú
21-51-12
ALL ú ú 03 Page 805 ú Feb 15/99
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
747-400
MAINTENANCE MANUAL
FLOW CONTROL AND SHUTOFF VALVE FILTERS - REMOVAL/INSTALLATION
_____________________________________________________________
1. General
_______
A. The flow control and shutoff valve filters prevent contamination from entering the pneumatic control circuits of the valve. Two filters are installed in each flow control and shutoff valve.
B. This procedure has instructions to do the following tasks:
(1)
Flow control and shutoff valve filter removal.
中國航空網(wǎng) m.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：747-400 AMM 飛機(jī)維護(hù)手冊 空調(diào) AIR CONDITIONING 2(42)
