S 434-050
(2)
Install the O-ring into the O-ring groove on the actuator.
S 824-051
(3)
Make sure the index screws on the actuator adapter electrical connection are aligned with the actuator.
S 424-052
(4)
Slowly install the actuator onto the actuator adapter
S 434-066
CAUTION: THE ACTUATOR MUST BE ALIGNED CORRECTLY WITH THE DRIVE
_______ HOUSING AND THE ACTUATOR ADAPTER BEFORE INSTALLING SCREWS.
(5)
Install one screw (1) to hold the actuator and the bonding lug to the actuator adapter.
S 434-055
(6)
Install three screws (1) and three washers (2) to hold the actuator to the actuator adapter.
S 434-036
(7)
Tighten all four screws (1) to 24-30 in-lbs of torque.
D. Do the Installation Test for the Valve
S 824-056
(1)
From the outer side of the airplane, turn the manual drive collar until the valve is in the open position.
S 864-057
(2)
Turn the EQUIP COOLING selector, on the overhead panel, P5, to the STBY position.
(3)
Supply electrical power (Ref 24-22-00/201).
(4)
Make sure the valve moves to the closed position.
S 794-059
(5)
Feel for leaks around the valve.
(a)
Small leaks are permitted.
(b)
You must repair a large leak.
S 864-037
S 714-058
EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú
21-58-12
ALL ú ú 02 Page 408 ú Jun 18/00
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
747-400 MAINTENANCE MANUAL
S 434-061
(6) Install the moisture shroud on the valve.
E. Put the Airplane to Its Usual Condition
S 864-038
(1)
Turn the EQUIP COOLING selector, on the P5 panel, to the NORM position.
S 864-039
(2)
Remove electrical power, if it is not necessary.
(Ref 24-22-00/201)
EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú
21-58-12
ALL ú ú 02 Page 409 ú Jun 18/00
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
747-400 MAINTENANCE MANUAL
E6/E9 VALVE - REMOVAL/INSTALLATION
__________________________________
1. General_______
A. This procedure has instructions to remove and install the E6/E9 valve. The valve is installed below the floor of the forward cargo compartment at Station 520.
TASK 21-58-13-004-001
2. E6/E9 Valve Removal (Fig. 401)___________________
A. References
(1)
24-22-00/201, Manual Control
(2)
AIPC 21-58-13 Fig. 1
(3)
WDM 21-58-25
(4)
SSM 21-58-06
B. Access
(1) Location Zone 121 Forward Cargo Compartment Forward Half, LH
C. Prepare for the Removal
S 864-002
CAUTION: DO NOT OPERATE THE ELECTRICAL/ELECTRONIC EQUIPMENT WHEN YOU DO
_______ THIS PROCEDURE. IF YOU OPERATE THE ELECTRICAL EQUIPMENT WHEN THE EQUIPMENT COOLING SYSTEM IS OFF, YOU CAN CAUSE THE ELECTRICAL EQUIPMENT TO BECOME TOO HOT.
(1)
Remove the electrical power (Ref 24-22-00/201).
S 014-003
(2)
If it is necessary, remove the left floor panel of the forward cargo compartment at Station 520.
D. Remove the Valve
S 034-004
(1)
Disconnect the electrical connector, DV449, from the valve.
(2)
Remove the clamps (4 locations) on each end of the valve.
S 034-005
EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú
中國航空網 m.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：747-400 AMM 飛機維護手冊 空調 AIR CONDITIONING 2(108)
