(d)  
Push the faceplate lightly against the window frame until high spots on the window frame touch the faceplate.

 (e)  
From the fairing compound you prepared above, apply a sample bead to a piece of scrap metal. 1) Allow the sample bead to cure in the same atmospheric

 conditions as those of the faceplate.
 NOTE:  To make the compound cure faster, let warm air flow
____ around the area. Do not let the air temperature be more than 120°F (46°C) around the compound and the metal surfaces.
 S 438-019-B00
 CAUTION:_______DO NOT TIGHTEN THE BOLTS TOO MUCH. BOLTS THAT ARE TOO TIGHT CAN CAUSE THE FACEPLATE OR THE WINDOW FRAME TO WARP. THIS CAN CAUSE YOU TOO CONTOUR THE FRAME AND THE SKIN AGAIN.
 (2)  Install each third or fourth bolt and tighten them enough to hold the faceplate in its position.
 NOTE:  The compound must come out from each point around the faying surface you repair.
 S 398-020-B00
 (3)  Remove the unwanted compound from the bolt holes and from around the frame.
 EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú

 56-11-00
 ALL  ú ú B01 Page 807 ú Jul 15/96
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
737-300/400/500MAINTENANCE MANUAL
 S 038-021-B00
 (4)  Remove the faceplate after the time shown under "Release from mold" in the Table I.
 ~.............................................................................. | | APPLICATION TIME AND CURE RATE | ................................................................................ | Material | Temperature |Application| Release | Sandable | Full Cure | | |MIN (°F) (°C) |Time (Hrs) | From Mold| (Hrs) | (Hrs) | | |MAY | | (Hrs) | | | ................................................................................ | EC 3587 | 75 |5 | 24 |3 | .25 | 2 | 4 | 48 | | -1/4 | | | | | | *[1] | | | 120 |5 | 46 |3 | -| 1 | 2 | 20 | ................................................................................ | EC 3587 | 75 |5 | 24 |3 | 1 | 8 | 16 | 96 | | -1 | | | | | | *[1] | | | 120 |5 | 46 |3 | -| 2 | 4 | 30 | 2..........…........….......…...........…..........…..........…................1
 *[1] Shore A durometer of 30 (min.) 5 second reading.
 NOTE: If you do not have the applicable hardness test equipment, it is
____ sufficient to make sure the sample component is not tacky. This check is important. If you allow the airplane to fly with a window installed on fairing compound with large wet areas, the cabin pressure can cause leaks around the window edge.
 TABLE I
 S 868-022-B00
 (5)  
Cut the unwanted compound from the window frame.

 S 398-023-B00

 (6)  
Fill all the empty areas that are more than 0.01 inch diameter with more compound.

 (7)  
Allow the compound to become hard.

 S 398-004-B00
 EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú

 56-11-00
 ALL  ú ú B01 Page 808 ú Jul 15/96
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
737-300/400/500MAINTENANCE MANUAL
 WINDOW NO. 1 - REMOVAL/INSTALLATION
___________________________________
 1.  General_______
 A.  This procedure contains two tasks. The first task is for the removal of the window No. 1. The second task is for the installation of the window No. 1.
 B.  The window No. 1 (windshield) is pressure sealed on installation with a gasket like, molded-in-position rubber seal. The beaded silicone rubber seal surface touches the window frame. This makes sure there is a good pressure and moisture tight seal around the window (Fig. 401). The pressure seal is part of the window assembly and is bonded to the edge of the windshield glass.
 C.  There is fairing compound applied to the window frame. This makes sure there is a good, flat surface for the window to touch. The thickness of the compound is different in different locations. At high spots on the window frame there is no compound.
 D.  Also shown in Fig. 401 are some items which are not components of the pressure seal. The items that are not part of the pressure seal are these:
　
中國航空網 m.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：737-300 400 500 AMM 飛機維護手冊 WINDOWS(9)