1)  Apply BMS5-95 class B1/2 to the underneath side of the head and to the shank of the fasteners (14) common to the upper control housing (4) and shim (13).
 2)  Install fasteners (14).
 S 825-010-B00
 (4)  Adjust the vertical position of the window if it is necessary:
 (a)  If you remove a shim washer (27) from one lower roller (25), remove one from the other lower roller or the window will turn.
 NOTE: You must also add a shim washer (10) to the upper
____
 roller (9).

 (b)  
Change the number of shim washers (27) between the lower bellcranks (22 and 28) and the lower rollers (25) as necessary. 1) Loosen the set screw (24) in the bellcrank. 2) Remove the special bolt (26). 3) Add or remove the shim washers (27). 4) Install the special bolt (26). 5) Tighten the set screw (24).

 (c)  
Change the number of shim washers (10) between the upper bellcrank (12) and the upper roller (9) as necessary (detail B). 1) Remove the special screw (7) from the upper bellcrank (12). 2) Add or remove shim washers (10). 3) Install the special screw (7).

 S 825-011-B00
 (5)  Adjust the position of the rollers in the tracks if it is necessary (detail B).
 (a)  If the upper roller (9) does not move freely in the upper track, change the number of shim washers (10) between the upper bellcrank (12) and the upper roller (9): 1) Remove the special screw (7) from the upper bellcrank (12).
 EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú

 56-12-11
 ALL  ú ú B02 Page 508 ú Mar 12/01
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
737-300/400/500MAINTENANCE MANUAL
 2) Add or remove the shim washers (10). 3) Install the special screw (7).
 (b)  If a lower roller (25) does not move freely in the lower track, change the number of shims (21) under the lower control housing (6 or 23) as necessary: 1) Loosen the attachment bolts (19) which attach the lower
 control housings (6 or 23) to the window rim.
 NOTE: Pull the bulb pressure seal (17) out of the groove
____ in the window rim to get access to the countersunk bolt.
 2)  Pull out the bolts and gently pull the housing from the window rim and corner fitting as necessary to get access to the shims (21).
 3) Add or remove the shims (21). 4) Install the control housings (6 or 23).
 S 425-012-B00
 (6)
Do this task: "Window No. 2 Installation" (Ref 56-12-11/401).

 S 985-013-B00

 (7)  
Close and lock the window.

 S 225-014-B00

 (8)  
Make sure that the window is aligned with the skin in the tolerance (Section A-A).

 F.  Adjust the emergency exit release mechanism (Fig. 502).
 NOTE: For windows with an emergency exit release only.
____ S 825-015-B00
 (1)  Adjust the external release handle (5) if it is not aligned with the external skin:
 (a)  
Remove the cockpit trim panel below the window No. 2.

 (b)  
Increase or decrease the length of the turnbuckle (4) and turn the eccentric bushing (2) as necessary.

 (c)  
Install the lockwire or a lockclip on the turnbuckle (4).

 (d)  
Install the cockpit trim panel.

 EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú

 56-12-11
 ALL  ú ú B02 Page 509 ú Mar 12/01
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
737-300/400/500MAINTENANCE MANUAL
 S 715-024-B00
 (2)  Make sure that the window unlocks and opens when the external release handle is pulled.
 NOTE: The maximum force necessary to pull the external release
____
 handle is 110 pounds.

 S 985-016-B00
 (3)  
Make sure that the window unlocks, opens, closes and locks freely when the emergency release handle is aligned with the external skin.

 S 215-017-B00

 (4)  
Make sure the lower cam assembly (7) and the camshaft assembly (8) are engaged correctly (Section A-A).

 (a)  
Close and lock the window.

 (b)  
　
中國航空網 m.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：737-300 400 500 AMM 飛機維護手冊 WINDOWS(45)