(k)
Remove the three bolts (26) and the hub (23).
(l)
Remove the shims (27).
NOTE: Measure the thickness of the shims for installation
____
later.
S 034-004-B00
(3)
Remove the assist handle (5) from the door:
(a)
Remove the bolts (16), inner collar (15), outer collar (13), and nuts (14) from the door panel (1).
S 024-005-B00
(4)
Remove the door panel (1) from the door:
(a)
Remove the washers (24) and nuts (25) that attach the bottom of the door panel (1) to the retainers.
(b)
Pull the fasteners (18) from the top of the door panel (1).
(c)
Pull the fasteners (18) from the forward and aft edges of the door panel (1).
(d)
Remove the door panel (1) and the seal (17) from the door.
NOTE: The window (2) stays on the door panel (1).
____
TASK 52-13-21-404-006-B00
3. Aft Entry Door Lining and Insulation Installation (Fig. 401)
_________________________________________________
A. Special Tools and Equipment
(1)
Wrench - F70336-1
B.
References
(1)
25-61-35/201, Escape Slide Assembly (Door-Mounted)
C.
Consumable Materials
(1)
D00015 Grease - BMS 3-24
D.
Access
(1)
Location Zone
110 Aft Entry Door
E.
Procedure
S 424-014-B00
(1)
Install the door panel (1) on the door:
(a)
Put the door panel (1) and the seal (17) in the correct position on the door.
(b)
Push the fasteners (18) on the forward and aft edges of the door panel (1).
(c)
Push the fasteners (18) on the top of the door panel (1).
(d)
Install the washers (24) and nuts (25) that attach the bottom of the door panel (1) to the retainers.
EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú
52-13-21
ALL ú ú B02 Page 404 ú Mar 12/01
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
737-300/400/500MAINTENANCE MANUAL
S 434-008-B00
(2)
Install the assist handle (5) on the door:
(a)
Install the bolts (16), inner collar (15), outer collar (13), and nuts (14) to the door panel (1).
(b)
Use the F70336-1 wrench to tighten the nuts (14) on the assist handle (5).
S 434-009-B00
(3)
Install the handle (3) on the door:
(a)
Install the shims (27) between the door panel (1) and the hub (23) as necessary. 1) Apply grease, BMS 3-24, on the sides of the shims (27) as
you install them.
(b)
Install the hub (23) and its bolts (26).
(c)
Install the new lockwire on the bolts (26) as shown.
(d)
Install the mount (21) on the door panel with screws (12) and washers (20).
(e)
Install the foam filler (11).
(f)
Position the cover (10) over the mount (12).
(g)
Align the screws in the cover (10) with the slots in the mount (12) and move horizontally to lock the cover in place.
(h)
Install the screw (9) in the cover (10).
(i)
Position the inside handle (3) on the hub (23).
(j)
Install the washers (8) and nuts (7).
(k)
Install the cotter pins (6).
(l)
Install the insert (19) in the inside handle (3).
(m)
Make sure that a minimum clearance of 0.10 inch (2.54 mm) is between the cover (10) and the inside handle (3). 1) If the clearance is less than 0.10 inch (2.54 mm), add
shims.
S 424-017-B00
(4) Install the escape slide assembly (4) on the door (AMM 25-61-35/201).
EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú
中國航空網(wǎng) m.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：737-300 400 500 AMM 飛機維護手冊 艙門 DOORS 1(81)
