(a)
Add or remove the shims below the covers to change the flushness.
S 845-024-B00
(7)
Put the door back in its initial condition:
(a)
Remove the weight or the rigging simulator tool from the door.
(b)
Install the door lining (Ref 52-41-31/401).
(c)
Install the escape slide assembly (Ref 25-61-35/201).
(d)
Do this task: "Galley Service Door Test".
TASK 52-41-00-705-030-B00
4. Galley Door Adjustment (Soft Unlatching) (Fig. 501B)________________________________________
A. General
(1)
If the latch torque tubes are not adjusted correctly, the door handle can move too easily. This can cause the door to open accidentally (soft unlatching). This task is a special procedure to adjust the door if it opens accidentally (soft unlatching).
B.
Equipment
(1)
Maintenance stand
(2)
Modeling Clay
(3)
Petroleum Jelly
(4)
C52006-1 Rigging Simulator - Escape Slide
(5)
Rig Pin
C.
References
(1)
25-61-35/201, Escape Slide Assembly (Door-Mounted)
(2)
52-41-31/401, Forward Entry Door Lining and Insulation
D.
Access
(1)
Location Zone
106 Forward Galley Service Door
112 Aft Galley Service Door
E.
Procedure
(1)
Put a maintenance stand adjacent to the door.
S 225-027-B00
(2)
Do a check of the latch roller clearance (Fig. 507).
(a)
Adjust the latch roller clearance if it is not correct (Fig. 515).
S 845-026-B00
EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú
52-41-00
ALL ú ú B01A Page 505 ú Mar 12/02
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
737-300/400/500MAINTENANCE MANUAL
S 215-025-B00
(3)
Do a check of the latch crank overcenter:
(a)
Remove the escape slide assembly (Ref. 25-61-35/201).
(b)
Remove the door lining (Ref. 52-41-31/401).
(c)
Attach a 90-pound weight to the door approximately in the middle of the bottom half of the door. Attach a 60-pound weight approximately in the middle of the bottom half of the AFT door. 1) You may use the rigging simulator tool, C52006-1.
(d)
Do a check of the latch crank overcenter (Fig. 503).
(e)
Adjust the overcenter if it is not correct (Fig. 509).
(f)
If you adjust the latch crank overcenter, do all of the task to adjust the door.
NOTE: The overcenter adjustment affects several other door
____
adjustments.
(g) Make sure the door is back in its usual position. 1) Remove the weight or the rigging simulator tool from the
door. 2) Install the lining on the door (Ref 52-41-31/401). 3) Install the escape slide on the door (Ref 25-61-35/201).
TASK 52-41-00-705-041-B00
5. Galley Service Door Test
________________________
A. Special Tools and Equipment
(1)
C52008-1 Torque Wrench - Galley Door
B.
Access
(1)
Location Zone
106 Forward Galley Service Door
112 Aft Galley Service Door
C.
Procedure
NOTE: The airplane must be on its wheels to do this test.
____ S 865-042-B00
(1)
Open and close the door.
(a)
See that the applicable warning light on the P5 panel comes on when the door is not latched.
EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú
52-41-00
ALL ú ú B01A Page 506 ú Mar 12/02
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
737-300/400/500MAINTENANCE MANUAL
(b)
中國航空網 m.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：737-300 400 500 AMM 飛機維護手冊 艙門 DOORS 1(126)
