3. Fault Confirmation
__________________
A. Test Do the operational test of the TPIS (Ref. AMM TASK 32-49-00-710-001).
4. Fault Isolation
_______________
A. If the operationnal test does not give a maintenance message:
- do a check of ROTATING MECH-TPIS MLG, WHEEL 1 (7GV), ROTATING MECH-TPIS MLG, WHEEL 2 (9GV), ROTATING MECH-TPIS MLG, WHEEL 3 (6GV), ROTATING MECH-TPIS MLG, WHEEL 4 (8GV), ROTATING MECH-TPIS NLG, WHEEL 2 (5GV), ROTATING MECH-TPIS NLG, WHEEL 1 (4GV) to make sure that the mechanisms are in correct condition and move freely.
(1) If the operational test gives the maintenance message CHECK TPIU/ROTATING MECH WIRING:
- replace the DETECTOR UNIT-TPIS (2GV) (Ref. AMM TASK 32-49-34-000-001) and (Ref. AMM TASK 32-49-34-400-001).
「一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一1 EFF : 051-099, ∞∞32-49-00∞∞∞∞∞∞∞∞∞∞Page 239
May 01/05 CES (2) If the fault contains:
- do a check and repair the wiring from the TPIS (2GV) to the wheel 1 rotating mechanism (7GV) pins AA/1A, 1B to pins B/A, B (Ref. ASM 32-49/01)
- do a check and repair the wiring from the TPIS (2GV) to the wheel 2 rotating mechanism (9GV) pins AA/2A, 2B to pins B/A, B (Ref. ASM 32-49/01)
- do a check and repair the wiring from the TPIS (2GV) to the wheel 3 rotating mechanism (6GV) pins AA/3A, 3B to pins B/A, B (Ref. ASM 32-49/01)
- do a check and repair the wiring from the TPIS (2GV) to the wheel 4 rotating mechanism (8GV) pins AA/4A, 4B to pins B/A, B (Ref. ASM 32-49/01)
- do a check and repair the wiring from the TPIS (2GV) to the wheel 9 rotating mechanism (5GV) pins AA/9A, 9B to pins A/A, B (Ref. ASM 32-49/01)
- do a check and repair the wiring from the TPIS (2GV) to the wheel 10 rotating mechanism (4GV) pins AA/10A, 10B to pins A/A, B (Ref. ASM 32-49/01).
B. Test
(1) Do the test given in Para. 3.A.
TIRE PRESSURE INDICATING SYSTEM (TPIS) - TASK SUPPORTING DATA
_____________________________________________________________
1. Trouble Shooting Tire Pressure Transducer and Rotating Mechanism Faults
_______________________________________________________________________
A. Procedure
(1) The test equipment used is the Line Tester P/N 4306065051
(2) Preparation for the Test
(a) Remove the protection cover of the related rotating mechanism:
- for the NLG wheels (Ref. AMM TASK 32-49-15-000-001)
- for the MLG wheels (Ref. AMM TASK 32-49-16-000-005).
(b) Disconnect the electrical connector (1) of the pressure transducer from the rotating mechanism (2). (Ref. Fig. 301)
(c) Measure the tire pressure of the applicable wheel with a pressure gage and record the value.
(3) Test of a pressure transducer
(Ref. Fig. 301, 302)
NOTE : If the result of one of these tests is not satisfactory,
____ replace the related pressure transducer:
- (Ref. AMM TASK 32-49-15-000-001) and (Ref. AMM TASK 32-49-15-400-001) for the NLG wheel
- (Ref. AMM TASK 32-49-16-000-005) and (Ref. AMM TASK 32-49-16-400-005) for the MLG wheel
(a) Connect the electrical connector (1) to the plug P1 of the Line Tester.
(b) Do the check of the pressure (PR)
-------------------------------------------------------------------------------ACTION RESULT -------------------------------------------------------------------------------
On the Line Tester:
- set the switch C1 to PRESSURE
- push on the pushbutton PB1 On the display of the Line Tester:
- make sure that the tire pressure indication agrees with the pressure you measured with the gage with a tolerance of plus or minus 3 PSI
「一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一1 EFF : 051-099, ∞∞32-49-00∞∞∞∞∞∞∞∞∞∞Page 301
May 01/05 CES
Pressure Transducers and Rotating Mechanisms - Location
Figure 301
「一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一1 EFF : 051-099, ∞∞32-49-00∞∞∞∞∞∞∞∞∞∞Page 302
May 01/05 CES
中國航空網 m.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：A320 Trouble Shooting Manual 排故手冊 起落架 LANDING GEAR 2(94)
