(b) If there is no corrosion:
- dry the electrical connector of the N/W steering servo control
- make sure that the heat-shrink sleeve of the electrical connector is in good condition
- connect the electrical connector to the N/W steering servo control (6GC) and fold back the end of the heat-shrink sleeve on the connector to cover it fully.
(2) If there is no water:
- replace the SENSOR-N/W STRG FDBK,CTL CHAN (3GC) (Ref. AMM TASK 32-51-19-000-001) and (Ref. AMM TASK 32-51-19-400-001).
(3) If the fault continues:
- replace the BSCU (10GG) (Ref. AMM TASK 32-42-34-000-001) and (Ref. AMM TASK 32-42-34-400-001).
(4) If the fault continues:
- do a check and repair the wiring from the BSCU (10GG) to the feedback sensor (3GC) pins AB/15E, 15F, 8E, 8F, 9E, 9F to pins A/A, B, C, D, E, F (Ref. ASM 32-51/01).
(5) If the fault continues:
- do a check and repair the wiring from the BSCU (10GG) to the N/S steering servo control (6GC) pins AB/12E, 12F, 13E, 13F, 14E, 14F to pins A/G,H, E, F, C, D (Ref. ASM 32-51/01).
(6) If the fault continues:
- do a check and repair the wiring from the BSCU (10GG) to the feedback sensor (4GC) pins AB/14E, 14F, 10E, 10F, 11F, 11E to pins A/A,B, C, D, E, F (Ref. ASM 32-51/01).
(7) If the fault continues:
- do the check of the charge pressure of the nose landing gear shock absorber (Ref. AMM TASK 12-14-32-614-004)
「一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一1 EFF : ALL ∞∞32-51-00∞∞∞∞∞∞∞∞∞∞Page 224
May 01/05 CES
R **ON A/C 106-149, 221-299, 401-499,
A. If either the GND SCAN or the BITE test gives the maintenance message STEERING FEEDBACK CONTROL SENSOR (3GC):
- do a check for water (or moisture) in the electrical connector of the N/W steering servo control (6GC).
(1) If there is water:
- examine the electrical connector for corrosion
(a) If there is corrosion:
- replace the SERVO CTL-N/W STEERING (6GC) (Ref. AMM TASK 32-51-51-000-001) and (Ref. AMM TASK 32-51-51-400-001).
(b) If there is no corrosion:
- dry the electrical connector of the N/W steering servo control and connect it.
(2) If there is no water:
- replace the SENSOR-N/W STRG FDBK,CTL CHAN (3GC) (Ref. AMM TASK 32-51-19-000-001) and (Ref. AMM TASK 32-51-19-400-001).
(3) If the fault continues:
- replace the SENSOR-N/W STRG FDBK,MONITORING CHAN (4GC)
(4) If the fault continues:
- replace the BSCU (10GG) (Ref. AMM TASK 32-42-34-000-001) and (Ref. AMM TASK 32-42-34-400-001).
(5) If the fault continues:
- do a check and repair the wiring from the BSCU (10GG) to the feedback sensor (3GC) pins AB/15E, 15F, 8E, 8F, 9E, 9F to pins A/A, B, C, D, E, F (Ref. ASM 32-51/01).
(6) If the fault continues:
- do a check and repair the wiring from the BSCU (10GG) to the N/S steering servo control (6GC) pins AB/12E, 12F, 13E, 13F, 14E, 14F to pins A/G,H, E, F, C, D (Ref. ASM 32-51/01).
(7) If the fault continues:
- do a check and repair the wiring from the BSCU (10GG) to the feedback sensor (4GC) pins AB/14E, 14F, 10E, 10F, 11F, 11E to pins A/A,B, C, D, E, F (Ref. ASM 32-51/01).
(8) If the fault continues:
- do the check of the charge pressure of the nose landing gear shock absorber (Ref. AMM TASK 12-14-32-614-004)
「一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一1R EFF : 106-149, 221-299, 401-499, ∞∞32-51-00∞∞∞∞∞∞∞∞∞∞Page 225
Aug 01/05 CES
**ON A/C ALL
B. Do the test given in Para. 3.A.
「一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一1 EFF : ALL ∞∞32-51-00∞∞∞∞∞∞∞∞∞∞Page 226
May 01/04R
CES
TASK 32-51-00-810-812
Failure of the Nosewheel Steering Feedback Sensor (Monitoring Channel)
1. Possible Causes
_______________
- SERVO CTL-N/W STEERING (6GC)
- SENSOR-N/W STRG FDBK,MONITORING CHAN (4GC) R - SENSOR-N/W STRG FDBK,CTL CHAN (3GC)
- BSCU (10GG)
- wiring from the BSCU (10GG) to the feedback sensor (4GC)
- wiring from the BSCU (10GG) to the N/S steering servo control (6GC)
- wiring from the BSCU (10GG) to the feedback sensor (3GC)
2. Job Set-up Information
中國航空網(wǎng) m.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：A320 Trouble Shooting Manual 排故手冊 起落架 LANDING GEAR 2(103)
