Aug 01/05 CES
R (d) Open the circuit breaker 2GG and close the circuit breakers 1GG,
R 3GG and 4GG (the BSCU CHAN 2 is in command).
R (e) On the MCDU, get the STEERING DATA page for the BSCU CHAN 2:
R - On the SYSTEM REPORT/TEST/L/G page, push the line key adjacent
R to the BSCU2 indication.
R - On the BSCU CHAN 2 page, push the line key adjacent to the
R SPECIFIC DATA indication.
R - On the BSCU CHAN 2/SPECIFIC DATA page, push the line key
R adjacent to the STEERING DATA indication.
R (f) On the MCDU on the STEERING DATA page :
R - Push the line key adjacent to the REFRESH indication and make
R sure that the STRSELV parameter shows CLOSED.
R - Record the servovalve current ISTRSV parameter (ISV6).
R (g) On the nose wheels deactivation electrical box 5GC, set the lever
R to normal.
R (h) Close the circuit breaker 2GG.
R (i) Make sure that the value of (Isv5-Isv6) is less than or equal to
R plus or minus 1.92 mA.
R (j) If the value is not correct:
R - Replace the BSCU (10GG) (Ref. AMM TASK 32-42-34-000-001) and
R (Ref. AMM TASK 32-42-34-400-001).
R (k) Do steps (a) thru (i) again and do step (l).
R (l) Return the aircraft to service and make a record in the aircraft
R log book to monitor the NWS durint the next taxi operation and to
R assess the aircraft lateral deviation, if any, using the rudder
R trim input.
R 1_ Refer to the Close-Up part (5.A) and do the relevant steps.
R (5) If the BSCU output is correct, do a check of the NWS angle 3GC value
R with the NLG centering cams as reference.
R (a) Jack up the front of the aircraft (Ref. AMM TASK 07-11-00-581-R 003).
R NOTE : In the fully extended position of the shock absorber, the
____ R NLG is automatically centered (the nose wheel steering is R in the zero position).
R (b) Depressurize the Green hydraulic system (Ref. AMM TASK 29-10-00-R 864-001).
「一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一1 EFF : 106-149, 221-299, ∞∞32-51-00∞∞∞∞∞∞∞∞∞∞Page 284
Aug 01/05 CES
R (c) On the MCDU on the STEERING DATA page of the BSCU CHAN 1(CHAN 2):
R - Push the line key adjacent to the REFRESH indication,
R - Record the RVDTCOM value.
R (d) Make sure that RVDTCOM value is less than or equal to 0 deg. plus
R or minus 0.5 deg. for the BSCU CHAN 1 and BSCU CHAN 2.
R (e) If the NWS angle is not correct for the BSCU CHAN 1 and/or BSCU
R CHAN 2:
R - Do a check of the voltage at the nose wheel steering feedback
R sensor 3GC (Ref. AMM TASK 32-51-19-220-001)
R 1_ If the voltage is out of the specified limits, do the
R adjustment of the nose wheel steering "zero" position with the
R NLG centering cams as reference (Ref. AMM TASK 32-51-00-820-
R 002).
R (f) If an adjustement of the NWS "zero" position with the centering
R cams as reference was done, return the aircraft to service and
R make a record in the aircraft log book to monitor the NWS during
R the next taxi operation and to assess the aircraft lateral
R deviation, if any, using the rudder trim input.
R 1_ Refer to the Close-Up part (5.A) and do the relevant steps
R (6) If the NWS angle 3GC value is correct or if the voltage is in the
R specified limits, do an inspection/check of the NLG torque link plays
R (Ref. AMM TASK 32-21-00-200-003).
R (a) If the NLG torque link plays were adjusted, return the aircraft
R to service and make a record in the aircraft log book to monitor
R the NWS during the next taxi operation and to assess the aircraft
R lateral deviation, if any, using the rudder trim input.
R 1_ Refer to the Close-Up part (5.A) and do the relevant steps
R (7) If the NLG torque link plays are correct, do the adjustment of the
R nose wheel "zero" position:
R (a) with the NOSE WHEEL ALIGNMENT TOOL (JT2000AIRBUS) as reference if
R the tool is available
R - Do a check of the NWS "zero" position (Ref. AMM TASK 32-51-00-
R 220-001).
R If the nose wheels offset as shown on the tool display is out
R tolerance (more than plus or minus 0.5 degree), do the
R adjustment of the NWS "zero" position. (Ref. AMM TASK 32-51-00-
中國航空網 m.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：A320 Trouble Shooting Manual 排故手冊 起落架 LANDING GEAR 2(128)
