曝光臺 注意防騙 網曝天貓店富美金盛家居專營店坑蒙拐騙欺詐消費者

R  002). 
R  (f) If an adjustement of the NWS "zero" position with the centering 
R  cams as reference was done, return the aircraft to service and 
R  make a record in the aircraft log book to monitor the NWS during 
R  the next taxi operation and to assess the aircraft lateral 
R  deviation, if any, using the rudder trim input. 
R  1_  Refer to the Close-Up part (5.A) and do the relevant steps
R  (6) If the NWS ANGLE 3GC value is correct or if the voltage is in the 
R  specified limits, do an inspection/check of the NLG torque link plays 
R  (Ref. AMM TASK 32-21-00-200-003). 
R  (a) If the NLG torque link plays were adjusted, return the aircraft 
R  to service and make a record in the aircraft log book to monitor 
R  the NWS during the next taxi operation and to assess the aircraft 
R  lateral deviation, if any, using the rudder trim input. 
R  1_ Refer to the Close-Up part (5.A) and do the relevant steps

 201-220, 301-399, Aug 01/05 CES

R  (7) If the NLG torque link plays are correct, do the adjustment of the 
R  nose wheel "zero" position: 
R  (a) with the NOSE WHEEL ALIGNMENT TOOL (JT2000AIRBUS) as reference if 
R  the tool is available 
R  - Do a check of the NWS "zero" position (Ref. AMM TASK 32-51-00-
R  220-001). 
R  If the nose wheels offset as shown on the tool display is out 
R  tolerance (more than plus or minus 0.5 degree), do the 
R  adjustment of the NWS "zero" position. (Ref. AMM TASK 32-51-00-
R  820-003) and do the step (c). 
R  NOTE : There are possible causes of undemanded steering during____ 
R  taxi other a mechanical offset of the nose wheels. 
R  Thus if the NWS angle is correct as shown on the tool 
R  display, then it will be necessary to do the tawiway test 
R  to get an accurate rudder trim figure. 
R  (b) With the rudder trim figure as reference if the LASER ALIGNMENT 
R  TOOL is not available or if the nose wheels offset as shown on 
R  the tool display is within tolerance: 
R  - Do the taxi check procedure to get an accurate rudder trim 
R  figure. 
R  1_  Align the aircraft on the centerline.
R  2_  Make sure that the engines operate at the same power level.
R  3_  Release the parking brake.
R  4_  Let the aircraft roll with the rudder pedals or the N/WS
R  handwheels along the centerline. 
R  When the aircraft is aligned, release the rudder pedals and 
R  the N/WS handwheels then continue the taxi without input to 
R  make an estimate of the deviation. 
R  NOTE : The speed must be between 10 and 15 kts.____ 
R  5_  Align the aircraft again on the centerline with the rudder
R  pedals or the N/WS handwheels. 
R  6_  Give a rudder trim input opposite the aircraft deviation.
R  NOTE : Give the rudder trim inputs 1 degree by 1 degree, then____ 
R  0.5 degree by 0.5 degree to get a fine adjustment. 
R  7_  Do again the procedure and make an estimate of the new
R  deviation. 
R  8_  Align the aircraft again on the centerline and do again this
R  procedure until the aircraft goes straight.Then record the 
R  rudder trim value X1.

 「一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一1R EFF : 005-049, 055-099, 101-105, 151-199, ∞∞32-51-00∞∞∞∞∞∞∞∞∞∞Page 274
 201-220, 301-399, Aug 01/05 CES

R  9_  Do the same procedure on the same taxiway in the opposite
R  direction. 
R  Then record the trim value X2. 
R  NOTE : The procedure is done in each direction to make sure____ 
R  that the effects of cross-winds and/or runway cambers 
R  are not included. 
R  10__  Calculate the average X of the two values X1 and X2 that you
R  measured: 
R  X = (X1 + X2)/2 
R  Examples: 
R  X1 = +3.5 degree (L), X2 = +4.1 degree (L) 
R  X = (+3.5 + 4.1)/2 = +3.8 degree (L) 
R  X1 = +6 degree (L), X2 = -2 degree (R) 
R  X = (+6 - 2)/2 = +2 degree (L) 
　
中國航空網 m.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：A320 Trouble Shooting Manual 排故手冊 起落架 LANDING GEAR 2(123)