R (2) Do a check of the steering angle on the MCDU.

R  (a) On the MCDU, get the STEERING DATA for the BSCU SYS 1 and BSCU 
R  SYS 2: 
R  (Ref. Fig. 202/TASK 32-51-00-991-005) 
R  - On the MCDU, get the SYSTEM REPORT/TEST/L/G page (Ref. AMM TASK 
R  31-32-00-860-009). 
R  - On the SYSTEM REPORT/TEST/L/G page, push the line key adjacent 
R  to the BSCU1 indication. 
R  - Make sure that the N/WS handwheels and the rudder pedals are in 
R  the neutral position. 
R  - On the BSCU SYS 1 page, push the line key adjacent to the 
R  STEERING DATA indication. 
R  - Push the line key adjacent to the REFRESH indication. 
R  - Print the STEERING DATA page of the BSCU SYS 1. 
R  - Push the line key adjacent to the RETURN indication to get the 
R  SYSTEM REPORT/ TEST/L/G page. 
R  - On the SYSTEM REPORT/TEST/L/G page, push the line key adjacent 
R  to BSCU2 indication. 
R  - On the BSCU SYS 2 page, push the line key adjacent to STEERING 
R  DATA indication. 
R  - Push the line key adjacent to the REFRESH indication. 
R  - Print the STEERING DATA page of the BSCU SYS 2. 
R  - Put the line key adjacent to the RETURN indication to get the 
R  SYSTEM REPORT/TEST/L/G page. 
R  (b) Do a check of CAPT,FO, rudder pedal, steering command angle and 
R  BSCU RVDT input : CAPT ANGLE, FO ANGLE,Pedal angle,STEER ORDER 
R  and NWS ANGLE 3GC parameters : 
R  1 Make sure that the CAPT ANGLE value is less than or equal to 0_ 
R  deg. plus or minus 0.4 deg. for the SYS 1 and SYS 2. 
R  2 Make sure that the FO ANGLE value is less than or equal to 0_ 
R  deg. plus or minus 0.4 deg. for the SYS 1 and SYS 2. 
R  3 Make sure that the pedal angle value is less than or equal to_ 
R  0 deg. Plus or minus 0.1 deg. For the SYS 1 and SYS 2. 
R  4 Make sure that the STEERING ORDER value is 0 degree for the_ 
R  SYS 1 and SYS 2. 
R  5 Make sure that the difference between the NWS ANGLE 3GC SYS 1_ 
R  (value A) and NWS ANGLE 3GC SYS2 (value B) is less than or 
R  equal to 0.8 degrees. 
R  (c) If any of the above parameters is out of tolerances, do the 
R  applicable steps: 
R  1 If the CAPT ANGLE value is more than 0 deg. plus or minus 0.4_ 
R  deg. for the SYS 1 and/or SYS 2:

 「一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一1R EFF : 005-049, 055-099, 101-105, 151-199, ∞∞32-51-00∞∞∞∞∞∞∞∞∞∞Page 267
 201-220, 301-399, Aug 01/05 CES

R  - Replace the XMTR UNIT-N/W STRG HANDWHEEL,CAPT (1GC) (Ref. 
R  AMM TASK 32-51-11-000-001) and (Ref. AMM TASK 32-51-11-400-
R  001). 
R  - Do the steps (a) and (b) 1_ again and make sure that the 
R  CAPT ANGLE value is correct for the SYS 1 and SYS 2, if not 
R  do step 6_. 
R  2_  If the FO ANGLE value is more than 0 deg. plus or minus 0.4
R  deg. For the SYS 1 and/or SYS 2: 
R  - Replace the XMTR UNIT-N/W STRG HANDWHEEL,F/O (2GC) (Ref. AMM 
R  TASK 32-51-11-000-001) and (Ref. AMM TASK 32-51-11-400-001). 
R  - Do the steps (a) and (b) 2_ again and make sure that the FO 
R  ANGLE value is correct for the SYS 1 and SYS 2, if not do 
R  step 6_. 
R  3_  If the pedal angle value is more than 0 deg. plus or minus 0.1
R  deg. for the BSCU SYS 1 and/or the BSCU SYS 2: 
R  - Open the circuit breakers 15CE2 and 16CE2 (the ELAC2 is 
R  isolated). 
R  - On the SYSTEM REPORT/TEST/L/G page, push the line key 
R  adjacent to the BSCU1 indication. 
R  - On the BSCU SYS 1 page, push the line key adjacent to the 
R  STEERING DATA indication. 
R  - On the STEERING DATA page of the BSCU SYS 1, push the line 
R  key adjacent to the REFRESH indication. 
R  - Record the value of the pedal angle value (value A1). 
　
中國航空網(wǎng) m.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：A320 Trouble Shooting Manual 排故手冊 起落架 LANDING GEAR 2(119)