(2) On the overhead maintenance panel 50VU, make sure that the ON legend of the ENG/FADEC GND PWR/1(2) pushbutton switch is off. Make sure that a warning notice is in position to tell persons not to energize the FADEC 1(2).

 (3) Make sure that the access platform is in position.

 Subtask 78-31-49-010-140
 B. Make sure that the fan cowl doors are open: (Ref. TASK 71-13-00-010-040) FOR 1000EM1 437AL, 438AR FOR 1000EM2 447AL, 448AR
 Subtask 78-31-49-040-128
 C. Make sure that the thrust reverser is unserviceable (Ref. TASK 78-30-00-481-041).
 F 『 EEFF : ALL E Page 41778-31-49
 E E Feb 01/98 E E ECES E

 F  『
 E  C F M  E
 E  E

 E 56-5B E
 E E

 4. Procedure
_________
 (Ref. Fig. 402/TASK 78-31-49-991-301)
 Subtask 78-31-49-420-074

 A. Installation of the Upper Supply Pipe of the Left Latch
 (1) Remove the protective covers from the pipe ends.

 (2) Put the upper supply pipe in position on the forward frame.

 (3) Connect the upper supply pipe to the interface bracket with the nut.

 (4) TORQUE the nut to between 260 and 300 lbf.in (2.93 and 3.39 m.daN).

 (5) Connect the upper supply pipe to the upper latch.

 (6) TORQUE the coupling nut to between 130 and 150 lbf.in (1.46 and 1.69 m.daN).

 (7) Connect the interface hydraulic hose to the upper supply pipe.

 (8) TORQUE the coupling nut to between 113 and 125 lbf.in (1.27 and 1.41 m.daN).

 (9) Attach the upper half clamp to the upper hydraulic line bracket with the bolt and the washer.

 (10) TORQUE the bolt to between 27 and 30 lbf.in (0.30 and 0.33 m.daN). NOTE : Apply a witness line of finish paint EA4 blue 5991 (Material
____ No. CP2245) on all nuts and connections after they are torqued.
 5. Close-up
________
 Subtask 78-31-49-440-077

 A. Make the thrust reverser serviceable (Ref. TASK 78-30-00-081-041).
 F 『 EEFF : ALL E Page 41878-31-49
 E E Feb 01/98 E E ECES E Subtask 78-31-49-410-085

 F  『
 E  C F M  E
 E  E
 E  56-5B  E
 E  E

 B. Close Access
 (1) Make sure that the work area is clean and clear of tool(s) and other items.

 (2) Close fan cowl doors : (Ref. TASK 71-13-00-410-040)
 FOR 1000EM1
 437AL, 438AR
 FOR 1000EM2
 447AL, 448AR

 (3) Remove the access platform(s).

 (4) Remove the warning notice(s). Subtask 78-31-49-710-068
 C. Bleed the air from the thrust reverser hydraulic system. (Ref. TASK 78-30-00-710-040)
 F 『 EEFF : ALL E Page 41978-31-49
 E E Feb 01/98 E E ECES E

 F 『
 E C F M E
 E E
 E 56-5B E
 E E

 TASK 78-31-49-000-043

 Removal of the Lower Supply Pipe of the Left Latch
 WARNING : WEAR A FACE SHIELD WHICH IS RESISTANT TO HIGH PRESSURE JETS WHEN YOU
_______
 WORK ON PRESSURIZED SYSTEMS.

R WARNING : DO NOT GET THE FLUID ON YOUR SKIN OR IN YOUR EYES. IF YOU DO:
_______ R - FLUSH IT AWAY WITH CLEAN WATER R - GET MEDICAL AID.
 CAUTION : USE 2 WRENCHES TO REMOVE OR INSTALL THE TUBE COUPLING NUTS.
_______
 ONE WRENCH TO HOLD THE UNION AND ONE TO LOOSEN OR TIGHTEN THE
 COUPLING NUT. THIS WILL PREVENT DAMAGE TO THE HARDWARE.

 1. Reason for the Job
__________________
 Self Explanatory
 2. Job Set-up Information
______________________
 A. Fixtures, Tools, Test and Support Equipment
 -------------------------------------------------------------------------------REFERENCE QTY DESIGNATION -------------------------------------------------------------------------------
No specific container 1 USgal (4 L)
 No specific protective covers
 No specific warning notice
 No specific access platform 1 m (3 ft. 3 in.)

 B. Referenced Information
 -------------------------------------------------------------------------------REFERENCE DESIGNATION -------------------------------------------------------------------------------
71-13-00-010-040 Opening of the Fan Cowl Doors
 78-30-00-481-041 Make the Thrust Reverser Unserviceable for
 Maintenance
 78-31-49-991-302 Fig. 403

 F 『 EEFF : ALL E Page 42078-31-49
 E E May 01/05 E E ECES E E 56-5B E
　
中國航空網 m.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：A320飛機維護手冊 AMM EXHAUST 1(89)