(a) Put a warning notice to tell persons not to start the engine.
(2) Make sure that the engine 1(2) shutdown occurred not less than 5 minutes before you do this procedure.
F 『 EEFF : ALL E Page 41378-31-42
E E Feb 01/98 E E ECES E
F 『
E C F M E
E E
E 56-5B E
E E
(3) On the overhead maintenance panel 50VU:
(a) Make sure that the ON legend of the ENG/FADEC GND PWR/1(2) pushbutton switch is off.
(b) Put a warning notice to tell persons not to energize the FADEC 1(2).
Subtask 78-31-42-010-052
B. Get Access
(1) Open the fan cowl doors: (Ref. TASK 71-13-00-010-040)
FOR 1000EM1
437AL, 438AR
FOR 1000EM2
447AL, 448AR
(2) Put the access platform in position.
Subtask 78-31-42-040-051
C. Make the thrust reverser unserviceable (Ref. TASK 78-30-00-481-041).
Subtask 78-31-42-010-053
D. Open the thrust reverser doors: (Ref. TASK 78-36-00-010-040)
FOR 1000EM1
451AL, 452AR
FOR 1000EM2
461AL, 462AR
4. Procedure
_________
(Ref. Fig. 402/TASK 78-31-42-991-304)
Subtask 78-31-42-020-051
A. Removal of the Right Electrical Harness
(1) Use the softnose pliers to loosen the electrical connectors on the stow-switches of the upper and lower blocker doors.
(2) Use the softnose pliers to loosen the electrical connector of the beam electrical harness.
(3) Disconnect the electrical connectors.
F 『 EEFF : ALL E Page 41478-31-42
E E Feb 01/98 E E ECES E
F 『
E C F M E
E E
E 56-5B E
E E
INTENTIONALLY BLANK
F 『R E E Page 41578-31-42
E E May 01/05 E E ECES E F 『 E C F M E E E E 56-5B E F 『 E C F M E E E E 56-5B E F 『 E C F M E E E E 56-5B E
Right Electrical Harness
Figure 402/TASK 78-31-42-991-304- 13 (SHEET 1)
F EEFF : ALL 『E 78-31-42 Page 416
E E Feb 01/98
E E
ECES E
Right Electrical Harness
Figure 402/TASK 78-31-42-991-304- 23 (SHEET 2)
F EEFF : ALL 『E 78-31-42 Page 417
E E Feb 01/98
E E
ECES E
Right Electrical Harness
Figure 402/TASK 78-31-42-991-304- 33 (SHEET 3)
F EEFF : ALL 『E 78-31-42 Page 418
E E Feb 01/98
E E
ECES E
F 『
E C F M E
E E
E 56-5B E
E E
(4) Disconnect the electrical connector from the electrical junction box.
(5) Remove the nuts, the bolts and the clamps that attach the electrical harness to the tubes.
(6) Remove the nuts, the bolts and the clamps that attach the electrical harness to the supports.
(7) Remove the nut, the washer, the bolt and the clamp that attach the electrical harness to the two half clamps.
(8) Remove the electrical harness from the engine.
(9) Put protective covers on the electrical connectors.
F 『 EEFF : ALL E Page 41978-31-42
E E May 01/05 ERE
ECES E
F 『
E C F M E
E E
E 56-5B E
E E
TASK 78-31-42-400-044
Installation of the Right Electrical Harness
1. Reason for the Job
__________________
Self Explanatory
2. Job Set-up Information
______________________
A. Fixtures, Tools, Test and Support Equipment
-------------------------------------------------------------------------------REFERENCE QTY DESIGNATION -------------------------------------------------------------------------------
No specific softnose pliers
No specific warning notice
No specific access platform 1 m (3 ft. 3 in.)
R No specific Torque Wrench : range 5.00 to 35.00 lbf.in R (0.05 to 0.40 m.daN) No specific Torque Wrench : range 30 to 40 lbf.in 中國航空網 m.k6050.com 航空翻譯 www.aviation.cn 本文鏈接地址：A320飛機維護手冊 AMM EXHAUST 1(79)
