R  Deploy Switch Figure 601/TASK 78-31-17-991-300
 F EEFF : E E ECES  ALL  『E 78-31-17EEE Page 604 Feb 01/05

 F 『
 E C F M E
 E E
 E 56-5B E
 E E
 (2) No play should exist between the bushing and the lever.

 NOTE : Determine if play exists between the switch lever and the
____ bushing. This may affect electrical signal while the pivot door is in the deploy condition and may cause deploy signal failure (Ref. TASK 78-31-17-710-002).
 -------------------------------------------------------------------------------INSPECT/CHECK MAXIMUM REMARKS SERVICEABLE LIMITS -------------------------------------------------------------------------------
1. Examine the deploy switch for:
 A. Damage  No damage permitted If you find some damage, replace the deploy switch (Ref. TASK 78-31-17-000-001) and (Ref. TASK 78-31-17-400-001).
 2. Examine the trigger for:
 A. Damage  No damage permitted If you find some damage, replace the defective part (Ref. TASK 78-31-17-000-001) and (Ref. TASK 78-31-17-400-001).
 3. Examine the beam electrical harness, for:
 A. Cracks  None permitted If cracks are found, replace the harness (Ref. TASK 78-31-17-000-002) and (Ref. TASK 78-31-17-400-002).
 B. Damage threads  None permitted If the connector is damaged replace the harness (Ref. TASK 78-31-17-000-002) and (Ref. TASK 78-31-17-400-002).
 F 『 EEFF : ALL E Page 60578-31-17
 E E Feb 01/05 ERE
ECES  E

 F  『
 E  C F M  E
 E  E
 E  56-5B  E
 E  E

 -------------------------------------------------------------------------------INSPECT/CHECK MAXIMUM REMARKS SERVICEABLE LIMITS -------------------------------------------------------------------------------
C. Bent pins  None permitted  If the connector has bent pins replace the harness (Ref. TASK 78-31-17-000-002) and (Ref. TASK 78-31-17-400-002).
 D. Tightness  The blue mark of the deploy switch must be covered by the blue mark of the beam electrical  If the blue mark of thepressure switch can beseen, tighten theelectrical connector with
 harness connector.  softnose pliers.
 4. Examine the inner
 levers for:
 A. Damaged or missing pad  No damage permitted and No missing permitted  If the lever pad ismissing or damaged, replace the inner lever (Ref. TASK 78-31-17-000-003) and (Ref. TASK 78-31-17-400-003).
 B. Corrosion  None permitted  If the lever has corrosion, replace the inner level (Ref. TASK 78-31-17-000-003) and (Ref. TASK 78-31-17-400-003).
 5. Examine the outer
 levers and bushing for:
 A. Damaged lever or bushing  No damage permitted  If the lever or bushinghas damage, replace the lever or bushing (Ref. TASK 78-31-17-000-003) and (Ref. TASK 78-31-17-400-003).

 F 『 EEFF : ALL E Page 60678-31-17
 E E Feb 01/05 ERE
ECES E

 F  『
 E  C F M  E
 E  E
 E  56-5B  E
 E  E

 -------------------------------------------------------------------------------INSPECT/CHECK MAXIMUM REMARKS SERVICEABLE LIMITS -------------------------------------------------------------------------------
B. Corrosion 
C. Correct operation 
D. Lever and bushing 
play 
R  E. Damaged or missing 
R  pad 
R 
R 
R 
R 
R 
5. Close-up________
 Subtask 78-31-17-410-054
 A. Close Access

None permitted
Lever should turn fully and easily
No play should exist between the lever and bushing
No damage permitted
No missing pad permitted If the lever or bushing have corrosion, replace the outer lever or bushing (Ref. TASK 78-31-17-000-003) and (Ref. TASK 78-31-17-400-003).
If the lever is not easyto turn, clean the lever and bushing. if the lever is still not easy to turn, replace the lever and bushing (Ref. TASK 78-31-17-000-003) and (Ref. TASK 78-31-17-400-003).
If there is play betweenthe lever and bushing,replace the lever and bushing (Ref. TASK 78-31-17-000-003) and (Ref. TASK 78-31-17-400-003).
If the pad is missing or damaged, replace the outer lever (Ref. TASK 78-31-17-000-003) and (Ref. TASK 78-31-17-400-003).
 NOTE : You should apply a witness line of finish paint EA4 blue 5991
____ (Material No. CP2245) all nuts and connections when you have checked their torques.
　
中國航空網 m.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：A320飛機維護手冊 AMM EXHAUST 1(54)