(5) Attach the rod supply pipe to the interface bracket with the nut.

 (6) TORQUE the nut to between 610 and 700 lbf.in (6.89 and 7.91 m.daN).

 (7) Connect the interface hydraulic hose to the head supply hose.

 (8) TORQUE the coupling nut to between 540 and 600 lbf.in (6.10 and 6.78 m.daN).

 (9) Attach the flange and the upper half clamp to the upper hydraulic line bracket with the bolts and the nuts.

 (10) TORQUE the nuts to between 27 and 30 lbf.in (0.30 and 0.33 m.daN).

 (11) Position the two half clamps on the electrical harness and the rod supply pipe. Install the bolt, the washer, the clamp and the nut.

 (12) TORQUE the nut to between 27 and 30 lbf.in (0.30 and 0.33 m.daN). NOTE : Apply a witness line of finish paint EA4 blue 5991 (Material

____ No. CP2245) on all nuts and connections after they are torqued.
 5. Close-up
________
 Subtask 78-31-49-440-087

 A. Make the thrust reverser serviceable (Ref. TASK 78-30-00-081-041).
 F 『 EEFF : ALL E Page A40478-31-49
 E E Feb 01/98 E E ECES E Subtask 78-31-49-410-096

 F  『
 E  C F M  E
 E  E
 E  56-5B  E
 E  E

 B. Close Access
 (1) Make sure that the work area is clean and clear of tool(s) and other items.

 (2) Close the fan cowl doors: (Ref. TASK 71-13-00-410-040)
 FOR 1000EM1
 437AL, 438AR
 FOR 1000EM2
 447AL, 448AR

 (3) Remove the access platform(s).

 (4) Remove the warning notice(s).

 F 『 EEFF : ALL E Page A40578-31-49
 E E Feb 01/98 E E ECES E

 F  『
 E  C F M  E
 E  E

 E 56-5B E
 E E
 TASK 78-31-49-000-027

 Removal of the Upper Head Supply Hose
 WARNING : WEAR A FACE SHIELD WHICH IS RESISTANT TO HIGH PRESSURE JETS WHEN YOU
_______
 WORK ON PRESSURIZED SYSTEMS.

R WARNING : DO NOT GET THE FLUID ON YOUR SKIN OR IN YOUR EYES. IF YOU DO:
_______ R - FLUSH IT AWAY WITH CLEAN WATER R - GET MEDICAL AID.
 CAUTION : USE 2 WRENCHES TO REMOVE OR INSTALL THE TUBE COUPLING NUTS.
_______
 ONE WRENCH TO HOLD THE UNION AND ONE TO LOOSEN OR TIGHTEN THE
 COUPLING NUT. THIS WILL PREVENT DAMAGE TO THE HARDWARE.

 1. Reason for the Job
__________________
 Self Explanatory
 2. Job Set-up Information
______________________
 A. Fixtures, Tools, Test and Support Equipment
 -------------------------------------------------------------------------------REFERENCE QTY DESIGNATION -------------------------------------------------------------------------------
No specific container 1 USgal (4 L)
 No specific protective covers
 No specific warning notice
 No specific access platform 1 m (3 ft. 3 in.)
 No specific Torque Wrench : range 96.00 to 900.00 lbf.in

 (1.00 to 10.00 m.daN)
 B. Consumable Materials
 -------------------------------------------------------------------------------REFERENCE DESIGNATION -------------------------------------------------------------------------------
Material No. CP2245  *
 finish paint EA4 blue 5991 (Ref. 70-30-00)

 F 『 EEFF : ALL E Page A40678-31-49
 E E May 01/05 E E ECES E E 56-5B E

 F  『
 E  C F M  E
 E  E

 E E

 C. Referenced Information
 -------------------------------------------------------------------------------
REFERENCE DESIGNATION
 -------------------------------------------------------------------------------
71-13-00-010-040 Opening of the Fan Cowl Doors
 78-30-00-481-041 Make the Thrust Reverser Unserviceable for
 Maintenance
 78-31-49-991-314 Fig. 413

 3. Job Set-up
__________
 Subtask 78-31-49-941-087

 A. Safety Precautions
 (1) On the center pedestal, on the ENG panel 115VU:

 (a) Put a warning notice to tell persons not to start the engine.

 (2) Make sure that the engine 1(2) shutdown occurred not less than 5 minutes before you do this procedure.

 (3) On the overhead maintenance panel 50VU:

 (a) Make sure that the ON legend of the ENG/FADEC GND PWR/1(2) pushbutton switch is off.

 (b) Put a warning notice to tell persons not to energize the FADEC 1(2).

 Subtask 78-31-49-010-121
 B. Get Access
 (1) Open the fan cowl doors: (Ref. TASK 71-13-00-010-040)
　
中國航空網 m.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：A320飛機維護手冊 AMM EXHAUST 1(110)