(2) On the overhead maintenance panel 50VU, make sure that the ON legend of the ENG/FADEC GND PWR/1(2) pushbutton switch is off. Make sure that a warning notice is in position to tell persons not to energize the FADEC 1(2).
(3) Make sure that the access platform is in position.
Subtask 78-31-17-010-058
B. Get Access
(1) Make sure that the fan cowl doors are open (Ref. TASK 71-13-00-010-040): FOR 1000EM1 437AL, 438AR FOR 1000EM2 447AL, 448AR
(2) Make sure that the thrust reverser doors are open (Ref. TASK 78-36-00-010-040): FOR 1000EM1 451AL, 452AR FOR 1000EM2 461AL, 462AR
Subtask 78-31-17-040-055
C. Make sure that the thrust reverser is unserviceable (Ref. TASK 78-30-00-481-041).
F 『 EEFF : ALL E Page 41378-31-17
E E Feb 01/98 E E ECES E 4. Procedure
F 『
E C F M E
E E
E 56-5B E
E E
_________ (Ref. Fig. 401/TASK 78-31-17-991-301) Subtask 78-31-17-420-051
A. Installation of the Beam Electrical Harness WARNING : BEFORE THE USE OF SOLVENT, PROTECTIVE FILM OR SEALANT CAREFULLY
_______ READ THE APPLICABLE "MATERIAL SAFETY DATA SHEET" AND FOLLOW ALL LISTED SAFETY AND HEALTH PRECAUTIONS. USE THESE PRODUCTS IN AN AREA OPENED TO THE AIR AND WEAR PROTECTION GLOVES. THESE PRODUCTS ARE FLAMMABLE AND VAPOR IS DANGEROUS. THEY MAY CAUSE IRRITATION OF EYES, NOSE, THROAT AND SKIN. HIGH CONCENTRATIONS MAY CAUSE WEAKNESS, HEADACHE, NAUSEA, DIZZINESS AND IMPAIRED JUDGEMENT.
(1) Apply a layer of blindexite RT 342/2 (Material No. CP2318) on the harness flange surface that will contact the forward frame.
(2) Install the beam electrical harness through the hole in the forward frame.
(3) Connect the beam electrical harness to the blocker door deploy switch.
(4) Tighten the coupling nuts of the deploy switch connectors with soft nose pliers.
(5) Attach the beam electrical harness to the forward frame with the three bolts.
(6) TORQUE the bolts to between 70 and 80 lbf.in (0.79 and 0.90 m.daN).
(7) Connect the forward frame electrical harness to the beam electrical harness.
(8) Attach the deploy switch access door with the three screws.
(9) TORQUE the screws to between 35 and 45 lbf.in (0.39 and 0.50 m.daN).
F 『 EEFF : ALL E Page 41478-31-17
E E Feb 01/98 E E ECES E 5. Close-up
F 『
E C F M E
E E
E 56-5B E
E E
________ Subtask 78-31-17-410-051
A. Close Access
(1) Make sure that the work area is clean and clear of tool(s) and other items.
(2) Close the thrust reverser doors (Ref. TASK 78-36-00-410-040): FOR 1000EM1 451AL, 452AR FOR 1000EM2 461AL, 462AR
Subtask 78-31-17-440-051
B. Make the thrust reverser serviceable (Ref. TASK 78-30-00-081-041). Subtask 78-31-17-410-052
C. Close Access
(1) Close the fan cowl doors (Ref. TASK 71-13-00-410-040):
FOR 1000EM1
437AL, 438AR
FOR 1000EM2
447AL, 448AR
(2) Remove the warning notice(s).
(3) Remove the access platform(s). Subtask 78-31-17-710-051
D. Do an operational test of the thrust reverser system (Ref. TASK 78-31-00-710-042).
F 『 EEFF : ALL E Page 41578-31-17
E E Feb 01/98 E E ECES E
F 『
E C F M E
E E
E 56-5B E
E E
TASK 78-31-17-000-003 Removal of the Blocker Doors Actuation Levers
1. Reason for the Job
__________________
Self Explanatory
2. Job Set-up Information
______________________
A. Fixtures, Tools, Test and Support Equipment
-------------------------------------------------------------------------------REFERENCE QTY DESIGNATION -------------------------------------------------------------------------------
No specific warning notice
No specific access platform 1 m (3 ft. 3 in.)
B. Referenced Information
-------------------------------------------------------------------------------REFERENCE DESIGNATION -------------------------------------------------------------------------------
71-13-00-010-040 Opening of the Fan Cowl Doors 78-30-00-481-041 Make the Thrust Reverser Unserviceable for Maintenance 78-31-17-000-001 Removal of the Blocker Door Deploy Switch
中國航空網 m.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：A320飛機維護手冊 AMM EXHAUST 1(48)
