(2)
Put the mid stage tee duct (20) in position between the bleed
pressure regulator valve (5), the HP bleed valve (40), and the IP R bleed check valve (45). Use serviceable E-seals (15), E-seals (15), R E-seals (15)
and the couplings (10) to connect the duct to the valves.
(3) Tighten the nuts of the couplings:
CAUTION : MAKE SURE THE SMOOTH CIRCULAR SURFACE OF THE COUPLING IS
_______ RADIALLY OUTBOARD FROM THE ENGINE. DO NOT LET THE COUPLING TOUCH ENGINE COMPONENTS OR STRUCTURE. DAMAGE TO THE COMPONENTS OR STRUCTURE COULD OCCUR.
(a) Tighten the nuts of the couplings (10) sufficiently to hold the mid stage tee duct (20) in position. Do not torque the coupling nuts at this time.
(4)
If required, adjust the support links (50) so they do not put a load on the mid stage tee duct (20).
(5)
TORQUE the nuts on the support links to between 54 and 60 lbf.in
(0.61 and 0.67 m.daN). Safety the nuts with lockwire 0.032 in. (0.8mm) dia (Material No. CP8001) or lockwire 0.032 in. (0.8 mm) dia (Material No. CP8002).
(6)
Put the support links (50) in the brackets on the mid stage tee duct
(20) . Attach the links with the bolts (25), the washers (30), and the nuts (35). Make sure that the washers are installed with the countersink against the boltheads.
(7)
Tighten the nuts sufficiently to hold the mid stage tee duct (20) in position. Do not torque the nuts at this time.
(8)
Make sure that the mid stage tee duct (20) is in the correct
position.
(9)
TORQUE the nuts (35) to between 100 and 140 lbf.in (1.13 and 1.58
m.daN).
(10)
TORQUE the coupling nuts, as follows:
(a)
TORQUE the coupling nut to the value shown on the coupling.
(b)
Tap the perimeter of the coupling with a fiber hammer, then torque the coupling nut again.
(c)
Do the torque procedure two times, then torque the coupling nut again.
(11)
Remove the protective covers from the HP sense tube and the boss on the mid stage tee duct (20).
(12)
Install the union (55) in the boss on the mid stage tee duct (20).
(13)
Connect the HP sense tube to the union (55).
(14)
Make sure that the tube is in the correct position.
(15)
Torque the coupling nut: CAUTION : USE 2 WRENCHES TO REMOVE OR INSTALL THE TUBE COUPLING NUTS.
_______ ONE WRENCH TO HOLD THE UNION AND ONE TO LOOSEN OR TIGHTEN THE COUPLING NUT. THIS WILL PREVENT DAMAGE TO THE HARDWARE.
(a) TORQUE the coupling nut on the tube to 142 lbf.in (1.60 m.daN).
1EFF : ALL 1 36-11-49Page 420 1 1 Nov 01/00R 1 1 1CES 1
Subtask 36-11-49-720-056
B. Do this Test
(1)
Remove the warning notice from the HP ground connector.
(2)
Connect an air supply source 30 psi (2.07 bar) to the HP ground connector.
(3)
0n the panel 30VU, put the X-BLEED selector switch in the OPEN position.
(4)
Apply a stable pressure of 30 psi (2.07 bar) to the HP ground connector.
(5)
Make sure that there are no leaks at the junctions of the installed duct.
(6)
Disconnect the air supply source from the HP ground connector.
5. Close-up
________ Subtask 36-11-49-865-055
A. Remove the safety clip(s) and the tag(s) and close this(these) circuit breaker(s): 2HA1, 3HA1, 2HA2, 3HA2
Subtask 36-11-49-410-051
B. Close Access
(1)
Make sure that the work area is clean and clear of tool(s) and other items.
(2)
Close the thrust reverser cowl doors (Ref. TASK 78-36-00-410-040): FOR 1000EM1 451AL, 452AR FOR 1000EM2 461AL, 462AR
(3) Remove the access platform(s). Subtask 36-11-49-440-060
C. Make the thrust reverser serviceable (Ref. TASK 78-30-00-081-041).
1EFF : ALL 1 36-11-49Page 421 1 1 Nov 01/00R 1 1 1CES 1
Subtask 36-11-49-410-083
D. Close Access
(1) Close the fan cowl doors (Ref. TASK 71-13-00-410-040): FOR 1000EM1 437AL, 438AR FOR 1000EM2 447AL, 448AR
(2) Remove the warning notice(s). Subtask 36-11-49-862-056
E. De-energize the ground service network
(Ref. TASK 24-42-00-862-001).
1EFF : ALL 1 36-11-49Page 422 1 1 Nov 01/00R 1 1 1CES 1
TASK 36-11-49-000-044
Removal of the High Pressure Tee Duct
WARNING : MAKE SURE THAT THE PNEUMATIC SYSTEM IS DEPRESSURIZED BEFORE YOU START
中國航空網 m.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：A320飛機維護手冊 AMM PNEUMATIC 氣源 1(123)
