-
THE FLIGHT CONTROLS

 -
THE FLIGHT CONTROL SURFACES

 -
THE LANDING GEAR AND THE RELATED DOORS

 -COMPONENTS THAT MOVE.
 WARNING : MAKE SURE THAT THE GROUND SAFETY-LOCKS ARE IN POSITION ON THE LANDING
_______
 GEAR.

 1. Reason for the Job
__________________
 Refer to the MPD TASK: 323100-06
 2. Job Set-up Information
______________________
 A. Fixtures, Tools, Test and Support Equipment
 -------------------------------------------------------------------------------REFERENCE QTY DESIGNATION -------------------------------------------------------------------------------
No specific circuit breaker(s) safety clip(s)
 No specific safety barriers
 No specific warning notice

 B. Referenced Information
 -------------------------------------------------------------------------------REFERENCE DESIGNATION -------------------------------------------------------------------------------
24-41-00-861-002 Energize the Aircraft Electrical Circuits from the External Power 24-41-00-862-002 De-energize the Aircraft Electrical Circuits Supplied
 from the External Power 27-50-00-866-008 Extension of the Flaps on the Ground 27-50-00-866-009 Retraction of the Flaps on the Ground 31-32-00-860-009 Procedure to Get Access to the SYSTEM REPORT/TEST/L/G
 Page
 31-60-00-860-001 EIS Start Procedure

 1EFF : ALL 1 32-61-00Page 501 1 1 May 01/05 1 1 1CES 1

 -------------------------------------------------------------------------------
REFERENCE DESIGNATION -------------------------------------------------------------------------------
R R R R  31-60-00-860-002 32-00-00-481-001 32-00-00-860-001 32-00-00-860-002  EIS Stop ProcedureInstallation of the Safety Devices on the Landing Gears Flight Configuration Precautions with Electrical Power Ground Configuration after Flight Configuration with Electrical Power
 3. Job Set-up__________
 Subtask 32-61-00-941-051
 A. Safety Precautions 
R  (1) Put the safety barriers in position.
 (2) Make sure that the ground safety locks are on the landing gear (Ref. TASK 32-00-00-481-001).
 (3) On the panel 400VU: - make sure that the landing-gear control-lever 6GA is in the DOWN position - put a warning notice in position to tell persons not to operate the landing gear.
 Subtask 32-61-00-860-050
 B. Aircraft Maintenance Configuration
 (1) Energize the aircraft electrical circuits (Ref. TASK 24-41-00-861-002).
 (2) Fully extend the flaps (Ref. TASK 27-50-00-866-008).
 (3) Do the EIS start procedure (ECAM only) (Ref. TASK 31-60-00-860-001).
 (4) On the ECAM control panel (CP), push (in) the WHEEL pushbutton switch (P/BSW). Make sure that the WHEEL page shows on the ECAM lower display unit (DU).

 1EFF : ALL 1 32-61-00Page 502 1 1 May 01/05 1 1 1CES 1 Subtask 32-61-00-869-052

 C. Flight Configuration Precautions
 (1) Do the precautions for flight configuration (Ref. TASK 32-00-00-860-001) before you open the LGCIU circuit breakers.
 Subtask 32-61-00-865-052
 D. Make sure that this(these) circuit breaker(s) is(are) closed:
 -------------------------------------------------------------------------------PANEL DESIGNATION IDENT. LOCATION -------------------------------------------------------------------------------49VU ENGINE/2/FADEC A/AND EIU 2 2KS2 A05 49VU ENGINE/1/FADEC A/AND EIU 1 2KS1 A04 49VU FWS/FWC1/SPLY 3WW F01 121VU COM NAV/RAD ALTM/2 1SA2 K12 121VU COM NAV/RAD ALTM/1 1SA1 K11 121VU ENGINE/ENG2/FADEC B 4KS2 Q40 121VU EIS/FWC2/SPLY 2WW Q07 121VU ENGINE/ENG1/FADEC B/AND EIU 1 4KS1 R41
 Subtask 32-61-00-865-051
 E. Open, safety and tag this(these) circuit breaker(s):
 -------------------------------------------------------------------------------PANEL DESIGNATION IDENT. LOCATION -------------------------------------------------------------------------------
121VU HYDRAULIC/LGCIU/SYS2 2GA Q35
 Subtask 32-61-00-869-050
 F. Cockpit Configuration
R (1) On the panel 115VU, make sure that the ENG MASTER 1 and MASTER 2 R levers are in the OFF position.
 (2)
 On the panel 50VU, push (in) and release (out) the FADEC GND PWR 1 or 2 P/BSW. Make sure that the applicable P/BSW ON light comes on.

 (4)
 Get access to the L/G page on the MCDU (Ref. TASK 31-32-00-860-009).

R (3) Make sure that the throttle control levers are in the 0 (idle stop) R position.
 1EFF : ALL 1 32-61-00Page 503 1 1 Nov 01/98 1 1 1CES 1

 4. Procedure
_________ Subtask 32-61-00-710-050
 A. Operational Test of the Landing Gear NOT DOWN Warning
　
中國航空網 m.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：A320飛機維護手冊 AMM LANDING GEAR 起落架9(88)