R 1EFF : 005-049, 055-099, 101-149, 151-199, 1 32-51-00Page A521 1201-299, 301-399, 401-499, 1Aug 01/05 1 1 1CES 1 (6) Check of the play on the NLG cams
(a)
On the SENSOR-VOLTAGE TEST (F26792000) or SENSOR - VOLTAGE TEST set the selector switch to U1.
(b)
Manually move the wheels in steering mode on the RH stop. Record the voltage U1.
(c)
Manually move the wheels in steering mode on the LH stop. Record the voltage U1'.
(d)
From the voltage U1 and U1', calculate the average voltage U1".
(e)
Manually move the wheels in steering mode to get the voltage U1". NOTE : The angular travel of the nose wheels includes the NLG cam
____ play and the NLG torque link play.
Subtask 32-51-00-820-062
B. Set the NWS Zero Position CAUTION : IF THE SENSOR BOX HAS P/N E21336000, NEVER REMOVE THE SENSOR
_______ FROM THE GEARBOX. THE SENSOR AND THE GEARBOX ARE AN ASSEMBLY THAT YOU MUST NOT DISASSEMBLE ON THE AIRCRAFT. IF YOU REMOVE THE SENSOR FROM THE GEARBOX:
-YOU WILL CAUSE DAMAGE TO THE SENSOR BOX
-THE ADJUSTMENT OF THE SENSOR BOX WILL NO LONGER BE CORRECT. NOTE : When the shock absorber is fully extended, the NLG is
____ automatically in the center position (the nose wheel steering is in the zero position).
NOTE : Do not move the wheels manually in the steering mode when you do
____
the adjustment procedure.
(1)
Measure the secondary voltages U1 and U2 for the sensor 3GC
Make sure that :
U1 = U2 plus or minus 20 mV
(2)
If U1 is not equal to U2 plus or minus 20 mV, do these steps:
(a) Use a spatula to remove the sealant:
-
from the areas identified S.
-
from the housing of the worm screw (5).
R 1EFF : 005-049, 055-099, 101-149, 151-199, 1 32-51-00Page A522 1201-299, 301-399, 401-499, 1Aug 01/05 1 1 1CES 1 NOTE : Do not cause damage to the surface protections of these
____
parts.
(b)
Loosen the screws (2) to release the sensor.
(c)
Turn the worm screw (5) to get: U1 = U2 plus or minus 20 mV
(d)
TORQUE the screws (2) to between 0.29 and 0.35 m.daN (25.66 and
30.97 lbf.in).
(e)
Make sure that U1 = U2 plus or minus 20 mV. If not, do the adjustment again.
(3)
On the panel 402VU, set the A/SKID & N/W STRG switch to OFF.
(4)
Remove the SENSOR-VOLTAGE TEST (F26792000) or SENSOR - VOLTAGE TEST (F26792000-1) (3).
(5)
Connect the electrical connector (4) to the sensor box (1).
(6)
Apply a layer of SEALANTS (Material No. 09-008E) on the areas identified S.
(7)
Fill the housing of the worm screw (5) with SEALANTS (Material No. 09-008E).
(8)
Do the adjustment procedure again for the sensor 4GC (monitor channel).
(9) On the panel 402VU, set the A/SKID & N/W STRG switch to ON. Subtask 32-51-00-865-097
C. Remove the safety clip(s) and the tag(s) and close this(these) circuit breaker(s): 3GG, 4GG
5. Close-up
________ Subtask 32-51-00-581-057
A. Lower the aircraft to the ground (Ref. TASK 07-11-00-586-001).
R 1EFF : 005-049, 055-099, 101-149, 151-199, 1 32-51-00Page A523 1201-299, 301-399, 401-499, 1Aug 01/05 1 1 1CES 1 Subtask 32-51-00-740-057
B. Bite Test
(1) Do the Bite test of the BSCU (Ref. TASK 32-46-00-740-001). Subtask 32-51-00-942-064
C. Remove the Equipment
(1)
Make sure that the work area is clean and clear of tool(s) and other items.
(2)
Remove the warning notice(s).
(3)
Remove the ground support and maintenance equipment, the special and standard tools and all other items.
R 1EFF : 005-049, 055-099, 101-149, 151-199, 1 32-51-00Page A524 1201-299, 301-399, 401-499, 1Aug 01/05 1 1 1CES 1 **ON A/C 001-004, 051-054,
TASK 32-51-00-820-003
Adjustment of the NWS "Zero" Position with the Adjusting Tool F26630200 for A/C with NWS Sensor (3GC,4GC) P/N C24763000 using the Nose Wheel Alignment Tool
WARNING : PUT THE SAFETY DEVICES AND THE WARNING NOTICES IN POSITION BEFORE YOU
_______
START A TASK ON OR NEAR:
-
THE FLIGHT CONTROLS
-
THE FLIGHT CONTROL SURFACES
-
THE LANDING GEAR AND THE RELATED DOORS
-COMPONENTS THAT MOVE.
WARNING : MAKE SURE THAT THE GROUND SAFETY-LOCKS ARE IN POSITION ON THE LANDING
中國航空網 m.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：A320飛機維護手冊 AMM LANDING GEAR 起落架9(18)
