(d)
Move the aircraft and position the nose wheels on the greased steel plates (Ref. TASK 09-10-00-584-002)
(2) Installation of the NOSE WHEEL ALIGNMENT TOOL (JT2000AIRBUS) (Ref. Fig. 526/TASK 32-51-00-991-027, 527/TASK 32-51-00-991-035)
**ON A/C 005-049, 055-099, 101-149, 151-199, 201-299,
(Ref. Fig. 528/TASK 32-51-00-991-036)
**ON A/C 301-399,
(Ref. Fig. 528A/TASK 32-51-00-991-036-A)
**ON A/C 005-049, 055-099, 101-149, 151-199, 201-299, 301-399,
WARNING : BE CAREFUL WHEN YOU USE THIS TOOL, BECAUSE IT CONTAINS
_______
CLASS 2 LASER EQUIPMENT.
-
DO NOT LOOK DIRECTLY INTO THE BEAM
-
DO NOT POINT THE BEAM AT OTHER PERSONS. THE LASER CAN CAUSE INJURY IF YOU DO NOT OBEY THESE PRECAUTIONS.
(a)
Open the radome to get access to the reference point (first point) (Ref. TASK 53-15-11-010-001)
(b)
Do a mark on the NLG doors (second point)
NOTE : These two reference points will be used to set-up the
____
front target
(c) Make sure that the area under the center and rear sections of the fuselage is clear
-identify the reference points (11) and (12) under the fuserlage (Ref. TASK 08-22-00-200-001)
-install the target on the refence point (12)
NOTE : These two reference points will be used to set-up the rear
____
target
1EFF : 005-049, 055-099, 101-149, 151-199, 1 32-51-00Page A560 1201-299, 301-399, 1Aug 01/05R 1 1 1CES 1
Nose Wheel Aligment Tool
Figure 526/TASK 32-51-00-991-027
R 1EFF : 005-049, 055-099, 101-149, 151-199, 1 32-51-00Page A561 1201-299, 301-399, 401-499, 1Aug 01/05 1 1 1CES 1
Reference Points for the Front Target
Figure 527/TASK 32-51-00-991-035
1EFF : ALL 1 32-51-00 Page A562
1 1 Aug 01/05
1 1
1CES 1
Reference points for the rear target
Figure 528/TASK 32-51-00-991-036
1EFF : 001-049, 051-099, 101-149, 151-199, 1 32-51-00Page A563 1201-299, 401-499, 1Aug 01/05 1 1 1CES 1
Reference points for the rear target
Figure 528A/TASK 32-51-00-991-036-A
1EFF : 301-399, 1 32-51-00 Page A564
1 1 Aug 01/05
1 1
1CES 1
(d) Jack up the NLG axle enough to spin the two wheels (Ref. TASK 07-12-00-582-001)
(e) Refer to the manufacturer's instruction manual to install and set-up the Nose Wheel Alignment Tool
(f) Lower the aircraft on its wheels and move the axle jack away
(3) Energize the aircraft electrical circuits (Ref. TASK 24-41-00-861-002)
(4) Make sure that rhe N/WS handwheels and the rudder pedals are in the neutral position
(5) Pressurize the Green hydraulic system (Ref. TASK 29-10-00-863-001)
(6) Set the rudder trim to zero position.
(7) Jack up the NLG axle enough to spin the two wheels (Ref. TASK 07-12-00-582-001) - put a thick layer of COMMON GREASE (Material No. 04-004) on the pivoting cup of the axle jack - jack up the NLG axle enough to spin the two wheels
R **ON A/C 401-499,
R Subtask 32-51-00-860-077-A
R B. Aircraft Maintenance Configuration
R R (1) Move the aircraft and position the nosewheels on the square steel plates
R (a) Position a steel plate in front of the wheels
R R (b) Apply a thick layer of COMMON GREASE (Material No. 04-004) to the upper surface of the steel plate
R (c) Put the other steel plate on the top of the greased steel plate
R R (d) Move the aircraft and position the nose wheels on the greased steel plates (Ref. TASK 09-10-00-584-002)
1EFF : 005-049, 055-099, 101-149, 151-199, 1 32-51-00Page A565 1201-299, 301-399, 401-499, 1Aug 01/05 1 1 1CES 1 1EFF : 401-499, 1 32-51-00Page A566 1 1 Aug 01/05 1 1 1CES 1 1EFF : 005-049, 055-099, 101-149, 151-199, 1 32-51-00Page A567 1201-299, 301-399, 401-499, 1Aug 01/05 1 1 1CES 1
R (2) Installation of the NOSE WHEEL ALIGNMENT TOOL (JT2000AIRBUS)
R (Ref. Fig. 526/TASK 32-51-00-991-027, 527/TASK 32-51-00-991-035,
528/TASK 32-51-00-991-036)
R WARNING : BE CAREFUL WHEN YOU USE THIS TOOL, BECAUSE IT CONTAINS_______
R CLASS 2 LASER EQUIPMENT.
R - DO NOT LOOK DIRECTLY INTO THE BEAM
R - DO NOT POINT THE BEAM AT OTHER PERSONS.
R THE LASER CAN CAUSE INJURY IF YOU DO NOT OBEY THESE
R PRECAUTIONS.
中國航空網(wǎng) m.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：A320飛機維護手冊 AMM LANDING GEAR 起落架9(27)
