R  **ON A/C 401-499, 
R  Subtask 32-51-00-860-082-A 
R  C. Aircraft Maintenance Configuration 
R  (1) Lower the aircraft on its wheels and move the axle jack away 
R  (2) Depressurize the Yellow hydraulic system (Ref. TASK 29-10-00-864-002) 
R  (3) De- energize the electrical circuits (Ref. TASK 24-41-00-862-002) 
R  (4) Move the aircraft to remove the grease plates (Ref. TASK 09-10-00-
R  584-002) 
R  (5) Remove the tools 
R  (6) Close the radome (Ref. TASK 53-15-11-410-001) 
R  (7) Make sure that the work area is clean and clear of tool(s) and other 
R  items

__________________________________________________________ REMOVAL/INSTALLATION
____________________
 TASK 32-51-11-000-001
 Removal of the Transmitter Unit - Nose Wheel Steering Handwheel (1GC,2GC)
 WARNING : PUT THE SAFETY DEVICES AND THE WARNING NOTICES IN POSITION BEFORE YOU
_______
 START A TASK ON OR NEAR:

 -
THE FLIGHT CONTROLS

 -
THE FLIGHT CONTROL SURFACES

 -
THE LANDING GEAR AND THE RELATED DOORS

 -COMPONENTS THAT MOVE.
 1.
 Reason for the Job

__________________
 Self Explanatory

 2.
 Job Set-up Information

______________________
 A. Fixtures, Tools, Test and Support Equipment
 -------------------------------------------------------------------------------
REFERENCE QTY DESIGNATION
 -------------------------------------------------------------------------------
No specific blanking caps
 B. Referenced Information
 -------------------------------------------------------------------------------REFERENCE DESIGNATION -------------------------------------------------------------------------------
**ON A/C 001-049, 051-099, 101-105, 151-158, 201-210,
 32-51-11-991-001 Fig. 401 R **ON A/C 106-149, 159-199, 211-299, 301-399, 401-499,
 32-51-11-991-001-A Fig. 401A
 1EFF : ALL 1 32-51-11Page 401 1 1 Aug 01/05 1 1 1CES 1 **ON A/C ALL

 3. Job Set-up
__________
 Subtask 32-51-11-865-050

 A. Make sure that this(these) circuit breaker(s) is(are) open, safetied and tagged
 -------------------------------------------------------------------------------PANEL DESIGNATION IDENT. LOCATION -------------------------------------------------------------------------------
121VU HYDRAULIC/BRAKING AND STEERING/SYS2/SPLY 4GG M36 121VU HYDRAULIC/BRAKING AND STEERING/SYS2/CTL 3GG M35 121VU HYDRAULIC/BRAKING AND STEERING/SYS1/CTL 1GG M34 121VU HYDRAULIC/BRAKING AND STEERING/SYS1/IND AND/SPLY 2GG M33
 4. Procedure
_________
 **ON A/C 001-049, 051-099, 101-105, 151-158, 201-210,

 (Ref. Fig. 401/TASK 32-51-11-991-001) R **ON A/C 106-149, 159-199, 211-299, 301-399, 401-499,
 (Ref. Fig. 401A/TASK 32-51-11-991-001-A)
 **ON A/C ALL

 Subtask 32-51-11-010-050
 A. Removal of the Cover of the Panel 19VU (18VU)
 (1)
 Release the lock (2) and remove the handle (3) from the transmitter unit (8).

 (2)
 Remove the screws (5) and the washers (6).

 (3)
 Remove the screw (10) and the washer (11).

 (4)
 Release the fasteners (1) and remove the cover (4).

 1EFF : ALL 1 32-51-11Page 402 1 1 Aug 01/05 1 1 1CES 1

 Nose wheel Steering Handwheel
 Figure 401/TASK 32-51-11-991-001

R 1EFF : 001-049, 051-099, 101-105, 151-158, 1 32-51-11Page 403 1201-210, 1May 01/05 1 1 1CES 1

 Nose wheel Steering Handwheel.
 Figure 401A/TASK 32-51-11-991-001-A

R 1EFF : 106-149, 159-199, 211-299, 301-399, 1 32-51-11Page 404 1401-499, 1Aug 01/05 1 1 1CES 1 Subtask 32-51-11-020-050

 B. Removal of the Transmitter
 (1)
 Remove the screws (7).

 (2)
 Release the transmitter unit (8) from its housing and disconnect the electrical connector (9).

 (3)
 Remove the unit (8).

 (4)
 Put blanking caps on the disconnected electrical connectors.

 1EFF : ALL 1 32-51-11Page 405 1 1 May 01/03R 1 1 1CES 1

 TASK 32-51-11-400-001 Installation of the Transmitter Unit - Nose Wheel Steering Handwheel (1GC,2GC) WARNING : PUT THE SAFETY DEVICES AND THE WARNING NOTICES IN POSITION BEFORE YOU
_______
 START A TASK ON OR NEAR:

 -
THE FLIGHT CONTROLS

 -
THE FLIGHT CONTROL SURFACES

 -
THE LANDING GEAR AND THE RELATED DOORS
　
中國航空網 m.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：A320飛機維護手冊 AMM LANDING GEAR 起落架9(33)