Subtask 32-51-00-740-056
 B. Bite Test
 (1) Do the Bite test of the BSCU (Ref. TASK 32-46-00-740-001). Subtask 32-51-00-942-063
 C. Remove the Equipment
 (1)
 Make sure that the work area is clean and clear of tool(s) and other items.

 (2)
 Remove the access platform(s).

 (3)
 Remove the warning notice(s).

 (4)
 Remove the ground support and maintenance equipment, the special and standard tools and all other items.

R 1EFF : 005-049, 055-099, 101-149, 151-199, 1 32-51-00Page 596 1201-299, 301-399, 401-499, 1Aug 01/05 1 1 1CES 1 **ON A/C 001-004, 051-054,

 TASK 32-51-00-820-002
 Adjustment of the NWS "Zero" Position with the Adjusting Tool F26630200 for A/C with NWS Sensor (3GC,4GC) P/N C24763000, NLG Centering Cams as Reference
 WARNING : PUT THE SAFETY DEVICES AND THE WARNING NOTICES IN POSITION BEFORE YOU
_______
 START A TASK ON OR NEAR:

 -
THE FLIGHT CONTROLS

 -
THE FLIGHT CONTROL SURFACES

 -
THE LANDING GEAR AND THE RELATED DOORS

 -COMPONENTS THAT MOVE.
 WARNING : MAKE SURE THAT THE GROUND SAFETY-LOCKS ARE IN POSITION ON THE LANDING
_______
 GEAR.

 1. Reason for the Job
__________________
 Do this procedure when you adjust a gear box P/N C24764000 with the adjusting tool F26630200 and when you use the NLG centering cams as reference.
R
 2. Job Set-up Information
______________________
 A. Fixtures, Tools, Test and Support Equipment
 -------------------------------------------------------------------------------REFERENCE QTY DESIGNATION
 -------------------------------------------------------------------------------
No specific circuit breaker(s) safety clip(s)
 No specific warning placard
 No specific AC voltmeter (minimum range: 0-20V, accuracy: 1 mV,

 frequency: 50-2000 Hz)
 No specific Torque Wrench : range 0.00 to 1.20 m.daN

 (0.00 to 9.00 lbf.ft)
 F26630200 1 ADJUSTING TOOL - NWS GEARBOX
 F26792000 1 SENSOR-VOLTAGE TEST
 F26792000-1 1 SENSOR - VOLTAGE TEST

 1EFF : 001-004, 051-054, 1 32-51-00Page 597 1 1 Aug 01/05 1 1 1CES 1 B. Consumable Materials

 -------------------------------------------------------------------------------REFERENCE DESIGNATION -------------------------------------------------------------------------------
Material No. 04-015  USA BAC 5001 DACO-5073
 GREASE (Ref. 20-31-00)

 C. Referenced Information
 -------------------------------------------------------------------------------REFERENCE DESIGNATION -------------------------------------------------------------------------------
07-11-00-581-003  Lifting of the Aircraft at Forward Jacking Point, MLG Wheels on the Ground
 07-11-00-586-001 Lowering of the Aircraft at Forward Jacking Point,
 MLG Wheels on the Ground
 24-41-00-861-002 Energize the Aircraft Electrical Circuits from the

 External Power 29-10-00-864-001 Depressurize the Green Hydraulic System 32-46-00-740-001 BITE Test of the BSCU 32-51-19-000-001 Removal of the Nose Wheel Steering Feedback Sensor
 (3GC, 4GC) P/N C24763000 32-51-19-400-001 Installation of the Nose Wheel Steering Feedback
 Sensor (3GC, 4GC) P/N C24763000
 32-51-00-991-012 Fig. 509
 32-51-00-991-013 Fig. 510

 3. Job Set-up
__________
 Subtask 32-51-00-941-053
 A. General
 (1) Put a warning placard in the cockpit to tell persons not to operate R the landing gear or the N/WS.
 (2)
 On the panel 400VU, make sure that the L/G normal control lever is in the DOWN position.

 (3)
 On the nose gear leg, on the nose wheel steering deactivation electrical box, make sure that the towing lever is in the normal position (engaged position).

 1EFF : 001-004, 051-054, 1 32-51-00Page 598 1 1 Aug 01/05 1 1 1CES 1

 (4) Make sure that the N/WS handwheels and the rudder pedals are in the neutral position.
 Subtask 32-51-00-860-067
 B. Aircraft Maintenance Configuration
 (1)
 Jack up the front of the aircraft (Ref. TASK 07-11-00-581-003). NOTE : In the fully extended position of the shock absorber, the NLG

____ is automatically centered (the nose wheel steering is in the zero position).

 (2)
 Make sure that the Green hydraulic system is de-pressurized (Ref. TASK 29-10-00-864-001).

 (3)
 Energize the aircraft electrical circuits (Ref. TASK 24-41-00-861-002).
　
中國航空網 m.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：A320飛機維護手冊 AMM LANDING GEAR 起落架9(11)