1EFF : ALL 1 32-51-51Page 412 1 1 Aug 01/05 1 1 1CES 1 1EFF : ALL 1 32-51-51Page 413 1 1 Aug 01/05 1 1 1CES 1
R (2) Depressurize the reservoir of the Yellow hydraulic system.
R (Ref. TASK 29-14-00-614-001)
R Subtask 32-51-51-941-052-A
R B. Safety Precautions
R (1) In the cockpit, on the panel 400VU put warning notice(s) in position
R to tell persons not to operate the landing gear control lever.
R (2) On the steering handwheels (CAPT and F/O) and on the brake pedals,
R put warning notice(s) in position to tell persons not to operate
R them.
R (3) Put the warning notice(s) in position to tell persons not to
R pressurize the Yellow hydraulic system:
R - on the panel 40VU in the cockpit,
R - on the ground service panel of the Yellow hydraulic system, access
R door (196BB).
R (4) Put the safety barriers in position.
R (5) Put a container below the servo-control to drain the hydraulic fluid.
R **ON A/C ALL
Subtask 32-51-51-865-053
C. Open, safety and tag this(these) circuit breaker(s):
-------------------------------------------------------------------------------
PANEL DESIGNATION IDENT. LOCATION
-------------------------------------------------------------------------------
121VU HYDRAULIC/BRAKING AND STEERING/SYS2/SPLY 4GG M36
121VU HYDRAULIC/BRAKING AND STEERING/SYS2/CTL 3GG M35
121VU HYDRAULIC/BRAKING AND STEERING/SYS1/CTL 1GG M34
121VU HYDRAULIC/BRAKING AND STEERING/SYS1/IND AND/SPLY 2GG M33
4. Procedure
_________ (Ref. Fig. 402/TASK 32-51-51-991-002-A) Subtask 32-51-51-020-053-A
A. Removal of the Servo-Valve
(1)
Precaution NOTE : When you remove the rubber protective coating, use a spatula
____ to prevent damage to the surfaces of the components.
(2)
Remove the cap (4).
(3)
Connect a hose to the valve (3).
(4)
Slowly loosen the nut (2) to open the valve (3) and drain the hydraulic fluid.
(5)
When no more fluid flows out, remove the hose and tighten the nut (2) to close the valve (3).
(6)
Remove the sleeve (10)
(7)
Disconnect the electrical connector (5). Put blanking caps on the disconnected electrical connector.
(8)
Discard the sleeve (10).
(9)
Cut and remove the lockwire and remove the screws (6).
(10)
Remove the servo-valve (1).
(11)
Remove and discard the packing (7) and (9). NOTE : When you remove the servo -valve from the nose wheel steering
____ servo- control (6GC), the hydraulic fluid in its body will flow out and can get on the servo-valve electrical connectors. Clean and dry them before the subsequent step.
(12)
Put the blanking caps on the electrical connectors (8).
1EFF : ALL 1 32-51-51Page 414 1 1 Aug 01/05R 1 1 1CES 1
Nose Wheel Steering Servo-Valve Figure 402/TASK 32-51-51-991-002-A
1EFF : 1 1R 1CES ALL 1 11 1 32-51-51 Page 415 Aug 01/05
TASK 32-51-51-400-002
Installation of the Nose Wheel Steering Servo-Valve
1. Reason for the Job
__________________
Self Explanatory
2. Job Set-up Information
______________________
A. Fixtures, Tools, Test and Support Equipment
-------------------------------------------------------------------------------REFERENCE QTY DESIGNATION
中國航空網 m.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：A320飛機維護手冊 AMM LANDING GEAR 起落架9(68)
