(4) Remove the ground support and maintenance equipment, the special and

 standard tools and all other items.

 1EFF : ALL 1 28-12-00Page 613 1 1 May 01/04 1 1 1CES 1 1EFF : ALL 1 28-12-00Page 614 1 1 Feb 01/05 1 1 1CES 1 1EFF : ALL 1 28-12-00Page 615 1 1 Feb 01/05 1 1 1CES 1

R  TASK 28-12-00-210-001 
R  Visual Check of Vent Surge Tank Burst Disc (EXTERNAL) 
R  WARNING : PUT THE SAFETY DEVICES AND THE WARNING NOTICES IN POSITION BEFORE YOU_______ 
R  START A TASK ON OR NEAR: 
R  - THE FLIGHT CONTROLS 
R  - THE FLIGHT CONTROL SURFACES 
R  - THE LANDING GEAR AND THE RELATED DOORS 
R  - COMPONENTS THAT MOVE. 
R  WARNING : MAKE SURE THAT THE GROUND SAFETY-LOCKS ARE IN POSITION ON THE LANDING_______ 
R  GEAR. 
R  1. Reason for the Job__________________ 
R  Refer to the MPD TASK: 281200-01 
R  2. Job Set-up Information______________________ 
R  A. Fixtures, Tools, Test and Support Equipment 
R  -------------------------------------------------------------------------------
R  REFERENCE  QTY DESIGNATION 
R  -------------------------------------------------------------------------------
R  No specific  safety barriers 
R  No specific  warning notices 
R  No specific  access panel 2.5 m (8 ft. 2 in.) 
R  98D27803500001  1 TOOL-ZERO LOCKING, FLAP SLAT CTL LEVER 
R  B. Referenced Information 
R  -------------------------------------------------------------------------------
R  REFERENCE  DESIGNATION 
R  -------------------------------------------------------------------------------
R  28-12-41-000-001  Removal of the Overpressure Protector 46QM (47QM) 
R  28-12-41-400-001  Installation of the Overpressure Protector 46QM 
R  (47QM) 
R  28-12-00-991-020  Fig. 603

R  3. Job Set-up__________ 
R  Subtask 28-12-00-941-061 
R  A. Safety Precautions 
R  (1) Put the safety barriers in position. 
R  (2) Install the TOOL-ZERO LOCKING, FLAP SLAT CTL LEVER (98D27803500001) 
R  on the flap/slat control lever. 
R  (3) Put warning notices in the cockpit to tell persons not to operate the 
R  flaps or slats. 
R  (4) Put an access panel in position below the applicable zone 550 or 650. 
R  4. Procedure_________ 
R  Subtask 28-12-00-210-061 
R  A. Visual Check of the Vent Surge Tank Burst Disc (EXTERNAL) 
R  (Ref. Fig. 603/TASK 28-12-00-991-020) 
R  (1) Inspect the burst (safety) disc through the opening in access panel 
R  550CB(650CB). Make sure that: 
R  - the white cross on the burst (safety) disc can be clearly seen 
R  - the burst (safety) disc is in one piece. 
R  (2) If the burst (safety) disc is damaged, replace the overpressure 
R  protector assembly (Ref. TASK 28-12-41-000-001) (Ref. TASK 28-12-41-
R  400-001). 
R  5. Close-up________ 
R  Subtask 28-12-00-942-064 
R  A. Removal of Equipment 
R  (1) Remove the safety barriers. 
R  (2) Remove the warning notice(s). 
R  (3) Remove the access platform(s). 
R  (4) Remove the ground support and maintenance equipment, the special and 
R  standard tools and all other items.

R R  Vent Surge Tank Burst Disc - Location and Detail Figure 603/TASK 28-12-00-991-020
 1EFF : 1 1 1CES  ALL  1 111 28-12-00 Page 616 Feb 01/05

R PROTECTOR - OVERPRESSURE (46QM,47QM,96QM,102QM,103QM) - REMOVAL/INSTALLATION
____________________________________________________________________________ TASK 28-12-41-000-001 Removal of the Overpressure Protector 46QM (47QM) WARNING : PUT THE SAFETY DEVICES AND THE WARNING NOTICES IN POSITION BEFORE YOU
_______
 START A TASK ON OR NEAR:

 -
THE FLIGHT CONTROLS

 -
THE FLIGHT CONTROL SURFACES

 -
THE LANDING GEAR AND THE RELATED DOORS

 -COMPONENTS THAT MOVE. WARNING : MAKE SURE THAT THE GROUND SAFETY-LOCKS ARE IN POSITION ON THE LANDING
　
中國航空網 m.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：A320飛機維護手冊 AMM FUEL 燃油1(167)