R 5. Close-up________
R Subtask 28-11-42-410-052
R A. Close Access
R (1) Make sure that the work area is clean and clear of tool(s) and other
R items.
R (2) Install the applicable access panel (Ref. TASK 28-10-00-910-002),
R (Ref. TASK 57-27-11-400-002):
R - FOR 214QM, 215QM
R install 540RB
R - FOR 216QM, 217QM
R install 640RB.
R (3) Install the applicable NACA vent intake (Ref. TASK 28-10-00-910-001),
R (Ref. TASK 28-12-47-400-001):
R - FOR 214QM, 215QM
R install the LH wing NACA vent intake
R - FOR 216QM, 217QM
R install the RH wing NACA vent intake.
R Subtask 28-11-42-650-055
R B. Fuel Configuration
R (1) Refuel, defuel or transfer fuel as necessary (Ref. TASK 12-11-28-650-
R 003), (Ref. TASK 28-25-00-650-001) or (Ref. TASK 28-25-00-869-001).
R Subtask 28-11-42-942-051
R C. Removal of Equipment
R (1) Remove the safety barriers.
R (2) Remove the access platform(s).
R (3) Remove the ground support and maintenance equipment, the special and
R standard tools and all other items.
CAP/ADAPTOR - GRAVITY FILL (42QM,43QM,44QM,45QM) - REMOVAL/INSTALLATION
_______________________________________________________________________ TASK 28-11-43-000-001 Removal of the Gravity Fill Cap/Adaptor WARNING : PUT THE SAFETY DEVICES AND THE WARNING NOTICES IN POSITION BEFORE YOU
_______
START A TASK ON OR NEAR:
-
THE FLIGHT CONTROLS
-
THE FLIGHT CONTROL SURFACES
-
THE LANDING GEAR AND THE RELATED DOORS
-COMPONENTS THAT MOVE. WARNING : MAKE SURE THAT THE GROUND SAFETY-LOCKS ARE IN POSITION ON THE LANDING
_______
GEAR.
1. Reason for the Job
__________________
R R Self Explanatory
2. Job Set-up Information
______________________
A. Fixtures, Tools, Test and Support Equipment
-------------------------------------------------------------------------------REFERENCE QTY DESIGNATION -------------------------------------------------------------------------------
No specific safety barriers
No specific access platform 3.5 m (11 ft. 6 in.)
98D28004000000 1 SPANNER-OVERWING FILLER
1EFF : ALL 1 28-11-43Page 401 1 1 May 01/04 1 1 1CES 1 B. Referenced Information
-------------------------------------------------------------------------------REFERENCE DESIGNATION -------------------------------------------------------------------------------
28-10-00-910-001 Safety Procedures When You Do Work in a Fuel Tank
28-10-00-910-002 Access to the Fuel Tanks and the Work Areas
R 28-12-46-000-001 Removal of the Overpressure-Protector Outlet 28-25-00-650-001 Pressure Defuel 28-25-00-650-003 To Drain Remaining Fuel from the Wing Tanks and the Center Tank 57-27-11-000-002 Removal of the Access Panel (540HB, 540JB, 540KB, 540LB, 540MB, 540NB, 540PB, 540QB, 540RB, 550AB, 550BB, 550CB, 550DB, 560AB, 640HB, 640JB, 640KB, ....) 28-11-43-991-001 Fig. 401
3. Job Set-up
__________
Subtask 28-11-43-941-051
A. Safety Precautions
WARNING : OBEY THE SAFETY PROCEDURES WHEN YOU DO WORK IN A FUEL TANK.
_______
(1)
You must obey the Fuel Safety Procedures (Ref. TASK 28-10-00-910-001) when you do work in a fuel tank.
(2)
Put the safety barriers in position.
Subtask 28-11-43-650-050
B. Fuel Configuration
(1)
Defuel the applicable fuel tank (Ref. TASK 28-25-00-650-001).
(2)
Drain the remaining fuel from the applicable fuel tank (Ref. TASK 28-25-00-650-003).
1EFF : ALL 1 28-11-43Page 402 1 1 May 01/04 1 1 1CES 1R **ON A/C 001-049, 051-099, 101-149, 151-199, 201-299, 401-499,
Subtask 28-11-43-010-050
C. Get Access
(1)
Put the access platform below the applicable access panel 540PB(640PB).
(2)
Remove the applicable access panel (Ref. TASK 28-10-00-910-002), (Ref. TASK 57-27-11-000-002):
-
FOR 42QM, 44QM
中國航空網 m.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：A320飛機維護手冊 AMM FUEL 燃油1(152)
