曝光臺 注意防騙 網曝天貓店富美金盛家居專營店坑蒙拐騙欺詐消費者

R  (56724S0000) (Ref. CMM 272101). 
R  (6) Hold the piston rod (4) with the clamping jaws and TORQUE the eye-end 
R  (1) to between 10.5 and 14.5 m.daN (77.43 and 106.93 lbf.ft). 
R  (7) Remove the spanner and the clamping jaws from the eye-end (1) and the 
R  piston rod (4). 
R  (8) Immediately set the rudder servo-control (7) in a vertical position. 
R  (9) Make sure that the eye-end (1) points down. 
R 
R  NOTE : The rudder servo-control must stay in this position until the____ 
R  sealant is hard. 
R  (10) Make sure that the space between the end of the piston rod (4) and 
R  the thread of the eye-end (1) is fully sealed. 
R  (11) Put the lever (13) with the bushes (12) in the lever (11). 
R  (12) Install the bolt (5) with the bush (6), the washer (9) and the nut
 (8). 
R  (13) TORQUE the nut (8) to between 0.05 and 0.15 m.daN (4.42 and 13.27
 lbf.in). 
R  (14) Safety the nut (8) with a new cotter pin (10). 
R  (15) Apply the SEALANTS (Material No. 09-016) to the cotter pin (10), the 
R  nut (8), the washer (9) and the head of the bolt (5).

 

 5. Close-up
________ Subtask 27-24-51-420-054
 A. Install the rudder servo control (Ref. TASK 27-24-51-400-001). Subtask 27-24-51-942-059
 B. Put the aircraft back to the serviceable condition.
 (1)
 Make sure that the work area is clean and clear of tool(s) and other items.

 (2)
 Remove the warning notice(s).

 (3)
 Remove the ground support and maintenance equipment, the special and standard tools and all other items.

 

R  TASK 27-24-51-960-001 
R  Replacement of the Rudder Servo-Control Bearings 
R  1. Reason for the Job__________________ 
R  Self Explanatory 
R  2. Job Set-up Information______________________ 
R  A. Fixtures, Tools, Test and Support Equipment 
R  -------------------------------------------------------------------------------
R  REFERENCE  QTY DESIGNATION 
R  -------------------------------------------------------------------------------
R  No specific  1 WARNING NOTICE 
R  B. Referenced Information 
R  -------------------------------------------------------------------------------
R  REFERENCE  DESIGNATION 
R  -------------------------------------------------------------------------------

R  27-24-51-000-001  Removal of the Rudder Servo Control 
R  1025GM/2025GM/3025GM 
R  27-24-51-400-001  Installation of the Rudder Servo Control 
R  1025GM/2025GM/3025GM 
R  CMM 272101 
R  3. Job Set-up__________ 
R  Subtask 27-24-51-860-059 

R  A. Aircraft Maintenance Configuration 
R  (1) Put the rudder pedals in the neutral position. 
R  (2) Make sure that the rudder trim control is set at the zero position. 
R  (3) Put the WARNING NOTICE in the flight compartment to tell persons not 
R  to operate the flight controls.

 

R  Subtask 27-24-51-020-057 
R  B. Removal of the rudder servo-control 
R  (1) Remove the rudder servo control (Ref. TASK 27-24-51-000-001). 
R  (2) Send the rudder servo-control to a workshop. 
R  4. Procedure_________ 
R  Subtask 27-24-51-960-050 
R  A. Replacement of the rudder servo-control bearings 
R  (1) Replace the rudder servo-control bearings (Ref. CMM 272101). 
R  5. Close-up________ 
R  Subtask 27-24-51-420-056 
R  A. Install the rudder servo control (Ref. TASK 27-24-51-400-001). 
R  Subtask 27-24-51-942-060 
R  B. Put the aircraft back to the serviceable condition. 
R  (1) Make sure that the work area is clean and clear of tool(s) and other 
R  items. 
R  (2) Remove the warning notice(s). 
R  (3) Remove the ground support and maintenance equipment, the special and 
R  standard tools and all other items.

 

 SERVO CONTROL - RUDDER (1025GM,2025GM,3025GM) - INSPECTION/CHECK
________________________________________________________________
 TASK 27-24-51-200-001
R Check of the Rudder Servo Control Attachments
 1. Reason for the Job
　
中國航空網 m.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：A320飛機維護手冊 AMM FLIGHT CONTROLS 飛行操縱2(150)