R 1EFF : ALL 1 27-24-51Page 434 1 1 Aug 01/05 1 1 1CES 1
(4) Install the washer (77) and the locking plate (64) in the bracket
(65) of the rudder (2).
R
R (5) Put the clamp (10) on the servo control (5).
R (6) Put the servo control (5) in position at the bracket (52), (65).
R (7) Make sure that the items that follow are correctly installed in the
R brackets (52) and (65):
R - The locking plates (53) and (64)
R - The washers (58) and (77)
R - The bushes (34), (36), (73) and (75).
R
(8) Connect the servo control (5) to the bracket (52) of the vertical
stabilizer (1) as follows:
(Ref. Fig. 403A/TASK 27-24-51-991-003-A)
R NOTE : In this procedure it is necessary for two persons to install____
R the items that follow in the bracket (52):
R - The servo control (5)
R - The sealing rings (35).
R (a) Apply a thin layer of the COMMON GREASE (Material No. 04-004) to
R the sealing rings (35).
R (b) Attach the sealing rings (35) in position at the eye-end bearing
R of the servo control (5).
R (c) Use the two GAGE - FEELER 0.25 mm (0.0098 in.) thick to carefully
R move the servo control (5) into the bracket (52).
R (d) Align the eye-end bearing of the servo control (5) and the
R sealing rings (35). Do this with the bolt hole in the bracket
R (52).
R (e) Install the bolt (55) through the connection of the bracket (52)
and the servo control.
R (f) Install the washer (85), the washers (89) and the nut (86) on the
bolt (55).
R (g) TORQUE the nut (86) to between 7.0 and 8.0 m.daN (51.62 and 58.99
lbf.ft).
R (h) Install the locking cap (87) and the cotter pin (88).
R 1EFF : 004-049, 055-099, 101-149, 151-199, 1 27-24-51Page 435 1201-299, 301-399, 401-499, 1Aug 01/05 1 1 1CES 1
(9) Connect the servo control (5) to the bracket (65) of the rudder (2)
as follows:
(Ref. Fig. 404A/TASK 27-24-51-991-004-A)
R NOTE : In this procedure it is necessary for two persons to install____
R the items that follow in the bracket (65):
R - The servo control (5)
R - The sealing rings (74).
R (a) Apply a thin layer of the COMMON GREASE (Material No. 04-004) to
R the sealing rings (74).
R (b) Attach the sealing rings (74) in position at the eye-end bearing
R of the servo control (5).
R (c) Use the two GAGE - FEELER 0.25 mm (0.0098 in.) thick to carefully
R move the servo control (5) into the bracket (65).
R (d) Align the eye-end bearing of the servo control (5) and the
R sealing rings (74). Do this with the bolt hole in the bracket
R (65).
R (e) Install the bolt (62) through the connection of the bracket (65)
and the servo control (5).
R (f) Install the washer (95), the washers (90) and the nut (96) on the
bolt (62).
R (g) TORQUE the nut (96) to between 7.0 and 8.0 m.daN (51.62 and 58.99
lbf.ft).
R (h) Install the locking cap (97) and the cotter pin (98).
R (10) Apply a thin layer of the SPECIAL MATERIALS (Material No. 05-005)
R (Ref. TASK 51-75-13-916-002) to all attachment parts made of steel
R which you can see. Do not apply the SPECIAL MATERIALS (Material No.
R 05-005) to the spherical bearings of the servo control (5).
R
(11) Connect the spring rod (21) to the input lever (17) of the servo
中國航空網 m.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：A320飛機維護手冊 AMM FLIGHT CONTROLS 飛行操縱2(141)
