曝光臺 注意防騙 網曝天貓店富美金盛家居專營店坑蒙拐騙欺詐消費者

1) While on the System Setup Page, press the FMS Knob momentarily to activate the flashing cursor.
2) Turn the large FMS Knob to highlight the ILS CDI capture field in the GPS CDI Box.
3) Turn the small FMS Knob to select the desired mode and press the ENT Key.
COM
Configuration NOTE: 8.33 kHz VHF communication frequency channel spacing is not approved for use in the United States. Select the 25.0 kHz channel spacing option for use in the United States.
The COM Configuration Box on the System Setup Page allows the pilot to select 8.33 kHz or 25.0 kHz COM frequency channel spacing.
To change COM channel spacing:
1) While on the System Setup Page, press the FMS Knob momentarily to activate the flashing cursor.
2) Turn the large FMS Knob to highlight the channel spacing field in the COM Configuration Box.
3) Turn the small FMS Knob to select the desired spacing and press the ENT Key.
N
earest Airports
The Nearest Airports Box on the System Setup Page defines the minimum runway length and surface type used when determining the nine nearest airports to display on the MFD Nearest Airports Page. A minimum runway length and/or surface type can be entered to prevent airports with small runways or runways that are not of appropriate surface from being displayed. Default settings are zero feet (or meters) for runway length and “hard/soft” for runway surface type.
To select nearest airport surface matching criteria (any, hard only, hard/soft):
1) While on the System Setup Page, press the FMS Knob momentarily to activate the flashing cursor.
2) Turn the large FMS Knob to highlight the runway surface field in the Nearest Airports Box.
3) Turn the small FMS Knob to display and scroll through the runway options (any, hard only, hard/soft, water) and press the ENT Key when the desired selection is highlighted.
To select nearest airport minimum runway length matching criteria:
1) While on the System Setup Page, press the FMS Knob momentarily to activate the flashing cursor.
2) Turn the large FMS Knob to highlight the minimum length field in the Nearest Airport Box.
3) Turn the FMS Knobs to enter the minimum runway length (zero to 25,000 feet) and press the ENT Key.
C
DI/BARO Synchronization
See the Flight Instruments section for a discussion on synchronizing both PFD’s Course Deviation Indicators and the altimeter barometric settings.
190-00494-02 Rev. B Garmin G1000 Pilot’s Guide for the Cessna Citation Mustang 39
System ystem Overview verview
SYSTEM
OVERVIEW
FLIGHT
INSTRUMENTS EICAS AUDIO PANEL
& CNS
FLIGHT
MANAGEMENT
HAZARD
AVOIDANCE AFCS ADDITIONAL
FEATURES APPENDICES INDEX
Systemystem Statustatustatus Pageage
The System Status Page displays the status and software version numbers for all detected system LRUs. Pertinent information on all system databases is also displayed. Active LRUs are indicated by green check marks and failed LRUs are indicated by red “X”s. Failed LRUs should be noted and a Cessna service center or Garmin dealer informed.
Figure 1-33 Example System Status Page
The LRU, ARFRM, and DBASE Softkeys on the System Status Page select the list (LRU Info, Airframe, or Database) through which the FMS Knob can be used to scroll if all the information cannot appear on the screen.
The ANN TEST Softkey, when selected, causes an annunciation test tone to be played and lights all annunciators on the audio panels, the MFD Control Unit, and the AFCS Control Unit.
40 Garmin G1000 Pilot’s Guide for the Cessna Citation Mustang 190-00494-02 Rev. B
System ystem Overview verview
SYSTEM
OVERVIEW
FLIGHT
AUDIO PANEL EICAS INSTRUMENTS
& CNS
FLIGHT
MANAGEMENT
HAZARD
ADDITIONAL AFCS AVOIDANCE
INDEX APPENDICES FEATURES
Utility Pageage
For flight planning purposes, timers, trip statistics, and a scheduler feature are provided on the AUX - Utility Page. The timers available include a stopwatch-like generic timer, a total time in flight timer, and a record of the time of departure. Trip statistics—odometer, trip odometer, and average trip and maximum groundspeeds—are displayed from the time of the last reset. Refer to the Additional Features section for a dicussion on the Scheduler feature.
Figure 1-34 Utility Page
T
imers
The generic timer can be set to count up or down from a specified time (HH:MM:SS). When the countdown on the timer reaches zero the digits begin to count up from zero. If the timer is reset before reaching zero on a countdown, the digits are reset to the initial value. If the timer is counting up when reset, the digits are zeroed.
Setting the generic timer
1) Use the FMS Knob to select the AUX - Utility Page.
2) Press the FMS Knob momentarily to activate the flashing cursor.
　
中國航空網 m.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：Cessna Citation Mustang G1000 Integrated Flight Dec(22)