曝光臺 注意防騙 網曝天貓店富美金盛家居專營店坑蒙拐騙欺詐消費者

Aircraft
SymbolCommand BarsFigure 7-6 Cross-pointer Command BarsFigure 7-5 Single-cue Command BarsAircraft SymbolCommand Bars
Changing Command Bar format:
1) Use the FMS Knob to select the AUX - System Setup Page on the MFD.
2) Press the FMS Knob to activate the cursor.
3) Turn the large FMS Knob to highlight ‘Format Active’ in the ‘Flight Director’ box.
4) Turn the small FMS Knob to highlight the desired format.
’SNGL CUE’ to display Command Bars as a single cue (Aircraft Symbol in figure 7-5).
Or:
’X-POINTER’ to display Command Bars as a cross pointer (Aircraft Symbol in Figure 7-6).
If the attitude information being sent to the flight director becomes invalid or unavailable, the Command Bars are removed from the display. The flight director Command Bars also disappear if the pitch exceeds +30˚/-20˚ or bank exceeds 65˚.
370 Garmin G1000 Pilot’s Guide for the Cessna Citation Mustang 190-00494-02 Rev. B
Automatic utomatic utomatic Flight Control System ystem
SYSTEM
OVERVIEW
FLIGHT
AUDIO PANEL EICAS INSTRUMENTS
& CNS
FLIGHT
MANAGEMENT
HAZARD
ADDITIONAL AFCS AVOIDANCE
INDEX APPENDICES FEATURES
7.3 Vertical Modes
Table 7-2 lists the vertical modes with their corresponding controls and annunciations. The mode reference is displayed next to the active mode annunciation for Altitude Hold, Vertical Speed, and Flight Level Change modes. The NOSE UP/DN Wheel can be used to change the vertical mode reference while operating under Pitch Hold, Vertical Speed, or Flight Level Change Mode. Increments of change and acceptable ranges of values for each of these references using the NOSE UP/DN Wheel are also listed in the table.
Vertical Mode
Description
Control
Annunciation
Reference Range
Reference Change Increment
Pitch Hold
Holds the current aircraft pitch attitude; may be used to climb/descend to the Selected Altitude
(default)
PIT
-20° to +20°
0.5°
Selected Altitude Capture
Captures the Selected Altitude
*
ALTS
Altitude Hold
Holds the current Altitude Reference
ALT Key
ALT
nnnnn ft
Vertical Speed
Maintains the current aircraft vertical speed; may be used to climb/descend to the Selected Altitude
VS Key
VS
nnnn fpm
-5000 to +5000 fpm
100 fpm
Flight Level Change, IAS Hold
Maintains the current aircraft airspeed (in IAS or Mach) while the aircraft is climbing/descending to the Selected Altitude
FLC Key
FLC
nnn kt
80 to
250 kt
1 kt
Flight Level Change, Mach Hold
FLC
M .nnn
M 0.40 to 0.63
M 0.01
Vertical Path Tracking
Captures and tracks descent legs of an active vertical profile
VNV Key
VPTH
VNV Target Altitude Capture
Captures the Vertical Navigation (VNV) Target Altitude
**
ALTV
Glidepath
Captures and tracks the WAAS glidepath on approach
APR Key
GP
Glideslope
Captures and tracks the ILS glideslope on approach
GS
Takeoff
Commands a constant pitch angle and wings level on the ground in preparation for takeoff
GA Switch
TO
10°
Go Around
Disengages the autopilot and commands a constant pitch angle and wings level in the air
GA
8°
* ALTS armed automatically when PIT, VS, FLC, TO, or GA active, and under VPTH when Selected Altitude is to be captured instead of VNV Target Altitude
** ALTV armed automatically under VPTH when VNV Target Altitude is to be captured instead of Selected Altitude
Table 7-2 Flight Director Vertical Modes
190-00494-02 Rev. B Garmin G1000 Pilot’s Guide for the Cessna Citation Mustang 371
Automatic utomatic utomatic Flight Control System ystem
SYSTEM
OVERVIEW
FLIGHT
INSTRUMENTS EICAS AUDIO PANEL
& CNS
FLIGHT
MANAGEMENT
HAZARD
AVOIDANCE AFCS ADDITIONAL
FEATURES APPENDICES INDEX
Pitch Hold Mode (PIT)
When the flight director is activated (the FD Key is pressed) or switched (the XFR Key is pressed), Pitch Hold Mode is selected by default. Pitch Hold Mode is indicated as the active vertical mode by the ‘PIT’ annunciation. This mode may be used for climb or descent to the Selected Altitude (shown above the Altimeter), since Selected Altitude Capture Mode is automatically armed when Pitch Hold Mode is activated.
In Pitch Hold Mode, the flight director maintains a constant pitch attitude, the pitch reference. The pitch reference is set to the aircraft pitch attitude at the moment of mode selection. If the aircraft pitch attitude exceeds the flight director pitch command limitations, the flight director commands a pitch angle equal to the nose-up/down limit.
　
中國航空網 m.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：Cessna Citation Mustang G1000 Integrated Flight Dec(131)