曝光臺 注意防騙 網曝天貓店富美金盛家居專營店坑蒙拐騙欺詐消費者

Outer leather glove.
Body Generation of airborne
composite dust, fibers, char
material. Puncture wounds
from fibers.
Protective coverall with hood,
elastic wrist and ankles.
Booties are optional.
TO 00-105E-9
OPERATION PROTECTION CONSIDERATION EQUIPMENT
Cutting the composite with a
saw, pounding, or drilling.
Cutting with a saw will generate
heat, airborne particulate and
organic vapor, WITH OR
WITHOUT FIXANT.
Requirement is for the team in
direct contact with the debris
and anyone within close
proximity.
Table 3.8-4 Personal Protective Equipment Considerations (3 of 3)
3-91
Eye and FaceAirborne particulate Goggles with half-face
respirator.
Respiratory Airborne composite dust,
fibrous particulater eaching the
micron size range
Full-face respirator preferred:
combination filter (organic
vapor and particulate 99%
efficiency) R series filter is
needed when lubricates or
cutting fluids are used.
Head Fibrous particulate Protective coverall with hood
Foot Puncture from sharp objectsHard sole and toe working
shoes
Hand/
Forearm
Puncture wounds, residual
dust, char material or spilled
fluids.
Inner long-cuffed nitrile glove.
Outer leather glove.
Body Generation of airborne
particulate, fibers, char
material. Puncture wounds
from fibers.
Protective coverall with hood,
elastic wrist and ankles.
Cutting with a saw may cause
sparking. Sparks will destroy
the protective coverall . An
outer covering like rubber
apron or leather chaps can be
used to protect against
sparks.
Booties are optional.
TO 00-105E-9
Table 3.8-5 Glove Types
1
1
Lessons learned:
1. Never have enough.
2. Gloves too thin. Require frequent changes.
3. Use only powder-free gloves.
4. Get the right size. Mishap response involves manual labor. The wrong size will interfer with the job.
5. Close-fitting gloves should be used to avoid catching.
6. Short-cuffed gloves will not protect forearms from fiber puncture wounds.
7. Effectiveness of the plastic glove depends on the thickness.
3-92
(7) Mishap response requires more than one type of
glove. Leather, cowhide or Kevlar is chosen for fiber puncture
resistance and sharp or jagged metal and glass. Plastic
gloves are chosen for chemical and particulate resistence
and there are a number of plastic gloves to choose
from. A glove selection guide has been tabulated, based
on common mishap hazards, see above Table 3.8-5,
Glove Types.
GLOVE TYPE USE FOR
Neoprene Freon
Burnt Kapton ®
Leather, Kevlar ® Boron fiber puncture
Carbon fiber puncture
Radioactive material
Nitrile
Thick nitrile
Composite dust
JP-8 soot
Bloodborne pathogens (BBP)
Antifreeze
Hydrazine
Gasoline
Keresene
Hydraulic fluid
Jet fuel
BBP decontamination solution
Carbon fiber
Latex BBP
Butyl-rubber Battery electrolyte
Chemical warefare agents
Antifreeze
BBP decontamination solution
The selection criteria was based on minimizing the number of gloves
needed.
TO 00-105E-9
HOLD-DOWN SOLUTION TYPECOMMON NAMES PURPOSE
PAA fixant
Polyacrylic Acid
Floor wax
Carboset 525
Temporary surface coating to hold down loose
debris that could become airborne when
working around the debris at the mishap site.
PAA fixant can be removed if the sprayed
piece needs to be analyzed for investigation
reasons.
PAA has environmental concerns. Try not to
over-spray the ground.
Permanent fixant Corrosion Prevention
Compound (CPC),
MIL-C-16173, Grade 4,
Asbestos encapsulate
Permanent coating for long-term scrapped
debris storage.
It is not sprayed on debris that may need
laboratory analysis.
Tackifier Polychem, J-Tack, or Terra
Tack
Soil preparation used to eliminate the potential
of fiber and dust re-suspension for low
vegeation, dry soils--
Tackifier is used to keep hay and straw mulch
from becoming airborne. There should not be
an environmental concern when using it to hold
down dust.
(8) To hold down composite dust fixant application can
be performed following the control of the immediate safety
hazards. Additional application will take place depending
on the needs at the site. There are three different
3-93
Table 3.8-6 Fiber Hold-Down Solution(s) Rationale
TM
holddown solutions based on the performance requirement.
　
中國航空網 m.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：航空資料37(136)