曝光臺 注意防騙 網曝天貓店富美金盛家居專營店坑蒙拐騙欺詐消費者

) Manufacturing processes as defined in the SE Guide. Always used as Verbs.
To obtain a copy of the SE Guide contact: AECMA Gulledelle 94, B-1200 Bruxelles, Belgium.
Tel: +32-2775-81-10, Fax: +32-2775-81-11.
This manual does not use the ATA 100 Aircraft Maintenance Task Oriented Support System
(AMTOSS) or the ATA 100 Production Management Data Base (PMDB).
AIRCRAFT
DA 40 Series
AMM
Introduction
Doc # 6.02.01
Rev. 5 01-00-00 Page 3
20 Sep 2007
A. The ATA100 Numbering System
The ATA100 numbering system uses 3 pairs of numbers, for example:
57-50-xx
Chapter / System
(Wings)
Section / Subsystem
(Flaps)
Unit / Subject Number
(Not normally used)
The first pair of numbers show the system. System 57 is the Wings. Chapter 57 contains the data
for the wings.
The second pair of numbers show the subsystem. Subsystem 50 is Flaps. Chapter 57, section 50
contains the data for the flaps installation.
The third pair of numbers show a unit. A unit could be the flap itself. Only complex systems use unit
numbers.
For simple systems, the main chapter has all of the data and there are no section/subsystem breakdowns.
B. Groups of Chapters
The chapters are put together in these groups:
Group A Introduction Chapters 01 - 02
Group B Airplane General Chapters 03 - 12
Group C Airframe Systems Chapters 20 - 37
Group D Structure Chapters 51 - 57
Group E Propeller Chapter 61
Group F Power Plant Chapters 71 - 81
A separation sheet divides each chapter. The separation sheet shows the number of the chapter
and the title.
AIRCRAFT
Introduction
DA 40 Series
AMM
Page 4
20 Sep 2007 01-00-00 Doc # 6.02.01
Rev. 5
The main contents of each group of chapters is given below:
(1) Group A - Introduction
Chapter 1 tells you about the Airplane Maintenance Manual, and Chapter 2 tells you how to use
the Airplane Maintenance Manual.
(2) Group B - Airplane General
Chapter 05 contains the Scheduled Maintenance Checklist. Some tasks require a maintenance
procedure. The Scheduled Maintenance Checklist identifies the chapter in the manual that gives
the maintenance procedure for the task. It also tells you where to find general information.
Chapters 06 to 10 tell you about general procedures such as towing, parking and weighing.
Chapter 11 tells you about the placards and markings which are important for operating the
airplane.
Chapter 12 contains servicing tasks such as refueling and lubrication. It also contains data
about cleaning.
(3) Group C - Airframe Systems
Chapter 20 contains the standard practices for airframe maintenance.
Chapters 21 to 37 tells you about the airframe systems. They include the avionics systems
(such as communications (23)) and the mechanical systems (such as flight controls (27)).
Chapter 31 shows the location of the instruments. The chapter which is applicable to the system
gives the details. For example, Chapter 27 gives the details for the flap position indicator.
(4) Group D - Structure
Chapter 51 contains data about the design of the airframe. It also gives instructions for minor
repairs to the structure.
Chapters 52 to 57 tell you about each part of the structure.
AIRCRAFT
DA 40 Series
AMM
Introduction
Doc # 6.02.01
Rev. 5 01-00-00 Page 5
20 Sep 2007
(5) Group E - Propeller
Chapter 61 contains the maintenance procedures for the propeller. Refer to the propeller
manufacturer’s manual for other data.
(6) Group F - Power Plant
This group of chapters describes the engine and its systems which make the Power Plant. It
contains the maintenance procedures for maintenance on the airplane. Refer to the engine
manufacturer’s manual for other data.
C. Chapter Configuration
The first page of each Chapter shows the number of the chapter and the title. The second page
shows the contents. Where applicable, each chapter and section contains the topics that follow:
) Description and Operation.
) Trouble Shooting.
) Maintenance Practices. Where applicable the Maintenance Practices give data on these
procedures:
Servicing.
Removal and Installation.
Adjustment/Tests.
Checking/Testing.
Cleaning/Painting.
Repairs.
AIRCRAFT
Introduction
DA 40 Series
AMM
Page 6
20 Sep 2007 01-00-00 Doc # 6.02.01
Rev. 5
5. Page Numbering System
This manual uses the ATA 100 page block-numbering system. The page number is at the bottom on
the outer edge. It is adjacent to the chapter/section number.
Each topic in a section has numbers from these page blocks:
　
中國航空網 m.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：鉆石40系列AMM 1(17)