国产男女无遮挡_日本在线播放一区_国产精品黄页免费高清在线观看_国产精品爽爽爽

  • 熱門標簽

當前位置: 主頁 > 航空資料 > 國外資料 >

時間:2010-05-28 01:11來源:藍天飛行翻譯 作者:admin
曝光臺 注意防騙 網曝天貓店富美金盛家居專營店坑蒙拐騙欺詐消費者

been received, the pilot is expected to start a speed
reduction so that the aircraft will cross the fix,
initially, at or below the maximum holding airspeed.
e. When no delay is expected, the controller
should issue a clearance beyond the fix as soon as
possible and, whenever possible, at least 5 minutes
before the aircraft reaches the clearance limit.
f. Pilots should report to ATC the time and
altitude/flight level at which the aircraft reaches the
clearance limit and report leaving the clearance limit.
NOTEIn
the event of two‐way communications failure, pilots are
required to comply with 14 CFR Section 91.185.
g. When holding at a VOR station, pilots should
begin the turn to the outbound leg at the time of the
first complete reversal of the to/from indicator.
h. Patterns at the most generally used holding
fixes are depicted (charted) on U.S. Government or
commercially produced (meeting FAA requirements)
Low or High Altitude Enroute, Area and STAR
Charts. Pilots are expected to hold in the pattern
depicted unless specifically advised otherwise by
ATC.
NOTEHolding
patterns that protect for a maximum holding
airspeed other than the standard may be depicted by an
icon, unless otherwise depicted. The icon is a standard
holding pattern symbol (racetrack) with the airspeed
restriction shown in the center. In other cases, the airspeed
restriction will be depicted next to the standard holding
pattern symbol.
REFERENCEAIM,
Holding, Paragraph 5-3-7j2.
i. An ATC clearance requiring an aircraft to hold
at a fix where the pattern is not charted will include
the following information: (See FIG 5-3-2.)
1. Direction of holding from the fix in terms of
the eight cardinal compass points (i.e., N, NE, E, SE,
etc.).
2. Holding fix (the fix may be omitted if
included at the beginning of the transmission as the
clearance limit).
3. Radial, course, bearing, airway or route on
which the aircraft is to hold.
4. Leg length in miles if DME or RNAV is to be
used (leg length will be specified in minutes on pilot
request or if the controller considers it necessary).
5. Direction of turn if left turns are to be made,
the pilot requests, or the controller considers it
necessary.
6. Time to expect further clearance and any
pertinent additional delay information.
AIM 2/14/08
5-3-10 En Route Procedures
FIG 5-3-2
Holding Patterns
TYPICAL PROCEDURE ON AN ILS OUTER MARKER
EXAMPLES OF HOLDING
L OM M M
RUNWAY
VOR
VOR
TYPICAL PROCEDURE AT INTERSECTION
OF VOR RADIALS
HOLDING COURSE
AWAY FROM NAVAID
HOLDING COURSE
TOWARD NAVAID
VORTAC
15 NM DME FIX 10 NM DME FIX
TYPICAL PROCEDURE AT DME FIX
2/14/En Route Procedures 5−3−11
FIG 5−3−3
Holding Pattern Descriptive Terms
ABEAM
HOLDING SIDE
OUTBOUND
END
HOLDING
COURSE
OUTBOUND
INBOUND
NONHOLDING SIDE
FIX END
RECIPROCAL
FIX
j. Holding pattern airspace protection is based on
the following procedures.
1. Descriptive Terms.
(a) Standard Pattern. Right turns
(See FIG 5−3−3.)
(b) Nonstandard Pattern. Left turns
2. Airspeeds.
(a) All aircraft may hold at the following
altitudes and maximum holding airspeeds:
TBL 5−3−1
Altitude (MSL) Airspeed (KIAS)
MHA − 6,000’ 200
6,001’ − 14,000’ 230
14,001’ and above 265
(b) The following are exceptions to the
maximum holding airspeeds:
(1) Holding patterns from 6,001’ to
14,000’ may be restricted to a maximum airspeed of
210 KIAS. This nonstandard pattern will be depicted
by an icon.
(2) Holding patterns may be restricted to a
maximum speed. The speed restriction is depicted in
parenthesis inside the holding pattern on the chart:
e.g., (175). The aircraft should be at or below the
maximum speed prior to initially crossing the holding
fix to avoid exiting the protected airspace. Pilots
unable to comply with the maximum airspeed
restriction should notify ATC.
(3) Holding patterns at USAF airfields
only − 310 KIAS maximum, unless otherwise
depicted.
(4) Holding patterns at Navy fields only −
230 KIAS maximum, unless otherwise depicted.
(5) When a climb−in hold is specified by a
published procedure (e.g., “Climb−in holding
pattern to depart XYZ VORTAC at or above 10,000.”
or “All aircraft climb−in TRUCK holding pattern to
 
中國航空網 m.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址:航空信息手冊2008上(191)
国产男女无遮挡_日本在线播放一区_国产精品黄页免费高清在线观看_国产精品爽爽爽
国产精品久久7| 日韩在线高清视频| 国产福利一区视频| 国产精品久久久久久亚洲影视| 一区一区视频| 免费在线观看亚洲视频| 久久久久国产精品熟女影院| 国产精品视频xxx| 一区二区日本伦理| 黄色片免费在线观看视频| 久久一区免费| 亚洲永久激情精品| 欧美性受xxxx黑人猛交| 国产欧美精品一区二区| 国产成人看片| 日本新janpanese乱熟| 成人久久久久爱| 久热精品视频在线免费观看| 日韩av一区二区三区在线观看| jizzjizz国产精品喷水| 国产精品激情av电影在线观看| 日韩视频一二三| 91精品在线国产| 久久成人免费视频| 免费h精品视频在线播放| 深夜成人在线观看| 一区二区日本伦理| 国产精品自产拍在线观看中文| 国产精品对白刺激| 国语自产精品视频在线看 | 亚洲欧洲在线一区| 国产欧美韩日| 久久成人亚洲精品| 国产在线播放一区二区| 国产精品天天av精麻传媒| 亚洲熟妇无码另类久久久| 国产欧美一区二区三区另类精品| 国产精品久久久久久久久久久久 | 国产经典一区二区三区| 中文字幕一区二区三区精彩视频| 欧美污视频久久久| 国产成人久久精品| 日本精品一区二区三区不卡无字幕 | 国产精品久久久久影院日本| 国产日韩在线看片| 亚洲午夜精品国产| 久久精品人人做人人爽电影| 男人舔女人下面高潮视频| 精品乱码一区二区三区| 91精品国自产在线观看| 欧美亚洲视频在线观看| 久久91精品国产91久久跳| 国产精品伊人日日| 日韩高清专区| 精品久久久久久亚洲| 91精品国产综合久久久久久丝袜| 人人做人人澡人人爽欧美| 久热精品在线视频| 国产精品9999久久久久仙踪林| 欧美连裤袜在线视频| 中文字幕日韩精品无码内射 | 国内揄拍国内精品| 亚洲高清乱码| 国产精品涩涩涩视频网站| 草莓视频一区| 日韩欧美不卡在线| 欧美日韩国产成人在线观看| 国产激情久久久| 国产视频一区二区三区在线播放| 性欧美在线看片a免费观看| 国产精品视频一区国模私拍| 99精品一区二区三区的区别| 青青草原av在线播放| 国产999视频| 爽爽爽爽爽爽爽成人免费观看| 国产精品一区二区三| 日本国产在线播放| 亚洲最大成人在线| 国产精品传媒毛片三区| 久久久久久久97| 国产精品夜间视频香蕉| 男人的天堂狠狠干| 少妇特黄a一区二区三区| 久热精品视频在线观看一区| 日韩在线观看你懂的| 成人在线免费观看一区| 精品欧美一区二区精品久久| 日本在线视频www色| 一区二区三区四区免费视频 | 日本一区二区久久精品| 久久久久久国产精品美女| 国产精品免费久久久久影院| 国产av天堂无码一区二区三区| 成人免费91在线看| 狠狠97人人婷婷五月| 人人澡人人澡人人看欧美| 午夜精品一区二区三区av| 欧美激情第1页| 国产精品二区三区| 国产成人无码a区在线观看视频| 91精品国产777在线观看| 国产欧美日韩视频一区二区三区| 精品免费视频123区| 日韩免费黄色av| 欧美一区二区三区……| 亚洲精品视频一区二区三区 | 国产v亚洲v天堂无码| 99视频国产精品免费观看| 国产中文日韩欧美| 黄色免费高清视频| 欧美精品无码一区二区三区| 日本电影一区二区三区| 亚洲一区免费网站| 中文字幕一区综合| 欧美精品video| 国产99久久久欧美黑人| 国产精品成人品| 国产精品久久网| 国产精品久久7| 国产精品久久久久久av| 国产精品久久久久7777| 国产精品电影观看| 国产精品视频免费在线| 国产精品视频999| 国产精品久久久久久久久久久不卡 | 国产在线精品二区| 国产一区二区香蕉| 国产一区玩具在线观看| 欧美亚洲一级片| 黄色一级大片免费| 国产在线视频不卡| 国产一区二区精品免费| 国产免费一区二区三区香蕉精| 国产免费高清一区| 国产精品一区二区av| 97免费视频在线| 国产福利一区二区三区在线观看| 久久99久久精品国产| 精品国产一区久久久| 国产精品女主播| 久久成人精品一区二区三区| 欧美日韩国产成人在线观看| 亚洲视频导航| 亚洲乱码中文字幕久久孕妇黑人| 三年中文高清在线观看第6集| 日本黄网免费一区二区精品| 欧美日韩国产一二| 国产淫片av片久久久久久| 成人免费网视频| 国产传媒欧美日韩| 国产精品三级久久久久久电影| 久久国产精品电影| 亚洲成色www久久网站| 日本欧美国产在线| 狠狠精品干练久久久无码中文字幕| 国产中文字幕免费观看| 97久草视频| 日韩中文字幕在线看| 国产精品国产三级国产专区53| 亚洲一区二区高清视频| 日本a在线天堂| 国产资源第一页| 国产精品99久久99久久久二8| 精品国产欧美一区二区五十路 | 美女av一区二区三区| 五月婷婷综合色| 男人天堂手机在线视频| 成人av中文| 久久精品99久久久香蕉| 亚洲综合激情五月| 青草热久免费精品视频| 高清视频在线观看一区| 久精品国产欧美| 久久99久国产精品黄毛片入口| 少妇人妻互换不带套| 免费精品视频一区| 国产高清不卡无码视频| 国产精品久久久一区二区三区| 午夜精品一区二区三区四区| 黄页免费在线观看视频| 国产精品av网站| 欧美精品一区二区三区国产精品| 少妇高清精品毛片在线视频| 麻豆一区二区三区在线观看| 久久人人爽人人| 国产精品久久久久秋霞鲁丝| 亚洲精品乱码久久久久久蜜桃91 | 亚洲欧美精品| 国产综合在线看| 色老头一区二区三区| 亚洲人成人77777线观看| 国产在线一区二区三区四区| xxxx性欧美| 日本欧洲国产一区二区| 91久久精品日日躁夜夜躁国产| 美日韩精品免费观看视频| 欧美精品免费观看二区| 国产福利久久| 一区二区三区在线视频111| 欧美激情第六页|