曝光臺 注意防騙 網曝天貓店富美金盛家居專營店坑蒙拐騙欺詐消費者

handling, and normally, only rudder pressure is
necessary to correct for a crosswind.
BEFORE TAKEOFF CHECK
The before takeoff check is the systematic procedure
for making a check of the engine, controls, systems,
instruments, and avionics prior to flight. Normally, it is
performed after taxiing to a position near the takeoff
end of the runway. Taxiing to that position usually
allows sufficient time for the engine to warm up to at
least minimum operating temperatures. This ensures
adequate lubrication and internal engine clearances
before being operated at high power settings. Many
engines require that the oil temperature reach a
minimum value as stated in the AFM/POH before high
power is applied.
Air-cooled engines generally are closely cowled and
equipped with pressure baffles that direct the flow of
air to the engine in sufficient quantities for cooling in
flight. On the ground, however, much less air is forced
through the cowling and around the baffling.
Prolonged ground operations may cause cylinder
overheating long before there is an indication of rising
oil temperature. Cowl flaps, if available, should be set
according to the AFM/POH.
Before beginning the before takeoff check, the airplane
should be positioned clear of other aircraft. There
should not be anything behind the airplane that might
be damaged by the prop blast. To minimize
overheating during engine runup, it is recommended
that the airplane be headed as nearly as possible into
the wind. After the airplane is properly positioned for
the runup, it should be allowed to roll forward slightly
so that the nosewheel or tailwheel will be aligned fore
and aft.
During the engine runup, the surface under the airplane
should be firm (a smooth, paved, or turf surface if
possible) and free of debris. Otherwise, the propeller
may pick up pebbles, dirt, mud, sand, or other loose
objects and hurl them backwards. This damages the
propeller and may damage the tail of the airplane.
Small chips in the leading edge of the propeller form
stress risers, or lines of concentrated high stress. These
are highly undesirable and may lead to cracks and
possible propeller blade failure.
While performing the engine runup, the pilot must
divide attention inside and outside the airplane. If the
parking brake slips, or if application of the toe brakes
is inadequate for the amount of power applied, the
airplane could move forward unnoticed if attention is
fixed inside the airplane.
Each airplane has different features and equipment,
and the before takeoff checklist provided by the
airplane manufacturer or operator should be used to
perform the runup.
AFTER LANDING
During the after-landing roll, the airplane should be
gradually slowed to normal taxi speed before turning
off the landing runway. Any significant degree of turn
at faster speeds could result in ground looping and
subsequent damage to the airplane.
To give full attention to controlling the airplane during
the landing roll, the after-landing check should be
performed only after the airplane is brought to a
complete stop clear of the active runway. There have
been many cases of the pilot mistakenly grasping the
wrong handle and retracting the landing gear, instead
of the flaps, due to improper division of attention while
the airplane was moving. However, this procedure may
be modified if the manufacturer recommends that
specific after-landing items be accomplished during
landing rollout. For example, when performing a
short-field landing, the manufacturer may recommend
retracting the flaps on rollout to improve braking. In
this situation, the pilot should make a positive
identification of the flap control and retract the flaps.
CLEAR OF RUNWAY
Because of different features and equipment in various
airplanes, the after-landing checklist provided by the
manufacturer should be used. Some of the items may
include:
• Flaps . . . . . . . . . . . . . . . Identify and retract
• Cowl flaps . . . . . . . . . . . . . . . . . . . . . Open
• Propeller control . . . . . . . . . . . Full increase
• Trim tabs . . . . . . . . . . . . . . . . . . . . . . . . Set
PARKING
Unless parking in a designated, supervised area, the
pilot should select a location and heading which will
prevent the propeller or jet blast of other airplanes from
striking the airplane broadside. Whenever possible, the
airplane should be parked headed into the existing or
forecast wind. After stopping on the desired heading,
the airplane should be allowed to roll straight ahead
　
中國航空網 m.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：AIRPLANE FLYING HANDBOOK 飛機飛行手冊上(20)