71-00-00
AMM
DA 40 Series
Detail Steps/Work Items Key Items/References
(17) Connect the main fuel feed hose to the firewall.
(18) Connect the alternate air control cable: S Put the control cable in position through the guide attached to the alternate air control assembly. S Install the lock-nut onto the control cable outer sheath and tighten the lock-nut. S Push the control cable wire end through the swivel in the operating ring. S Make sure that the alternate air control lever in the cockpit is set to OFF. S Make sure that the alternate air assembly is set to the OFF position. S Move the alternate air control lever in the cockpit 3 mm (0.125 in) aft from OFF. S Tighten the screw which attaches the wire end to the swivel. S Install the P-clamps and cable ties which hold the Bowden-cable in the correct position. Fully forward. Inlet holes fully closed.
(19) Do a test for the correct operation of the alternate air control system. Refer to Section 76-00.
(20) Connect the throttle cable to the fuel injector: S Move the cable into position through the bracket at the bottom of the engine. S Install the front adjustment nut and washer on the outer sheath. Tighten the nut.
(21) Install the cable eye end onto the throttle cable: S Install the lock-nut onto the cable end. S Install the eye-end onto the cable end. S Tighten the lock-nut. Use a piece of lock-wire to make sure that the eye-end is installed correctly.
71-00-00
Power Plant
AMM
DA 40 Series
Detail Steps/Work Items Key Items/References
(22) Connect the cable eye end to the throttle lever at the fuel injector: S Move the attachment bolt into position in the throttle lever at the fuel injector. S Install a washer on the attachment bolt. S Install the eye end on the attachment bolt. S Install a second washer and a nut on the attachment bolt. Tighten the nut. From the engine side.
(23) Move the throttle lever in the cockpit between FULL and IDLE. The throttle control must be smooth in operation with no restrictions.
(24) Do a test for the correct operation of the throttle control system. Refer to Section 76-00.
(25) Connect the mixture control cable at the fuel injector: S Move the cable into position through the rubber grommets in the engine cooling baffles. S Install the top adjustment nut and washer onto the control cable outer sheath. S Push the cable through the support bracket at the bottom of the engine. S Install the bottom adjustment nut and washer on to the control cable outer sheath. Tighten the nut.
(26) Install the cable eye end onto the mixture cable: S Install the lock-nut on the cable. S Install the eye end on the cable. S Tighten the lock-nut. Use a piece of lock-wire to make sure that the eye end is installed correctly.
71-00-00
AMM
DA 40 Series
Detail Steps/Work Items Key Items/References
(27) Connect the mixture control cable eye end to the mixture lever at the fuel injector: S Move the long bolt into position in the mixture lever. S Install the spacer on the long bolt. S Install the eye end on the long bolt. S Install the nut and washer on the long bolt. Tighten the nut. From inboard.
(28) Move the mixture control lever in the cockpit between RICH and LEAN CUT-OFF. The mixture control must be smooth in operation with no restrictions.
(29) Do a test for the correct operation of the mixture control. Refer to Section 76-00.
(30) Connect the propeller control cable to the propeller governor: S Move the propeller cable into position through the rubber grommets in the engine cooling baffles. S Install the rear adjustment nut and washer onto the control cable outer sheath. S Push the cable through the support bracket at the bottom of the engine. S Install the front adjustment nut and washer on to the control cable outer sheath. Tighten the nut.
中國航空網 m.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：鉆石40飛機維護手冊 DA 40 SERIES AMM 5(7)
