71-00-00
AMM

DA 40 Series

Detail Steps/Work Items  Key Items/References 
(25)  Release the propeller control cable from the support bracket at the propeller governor: S Remove the front adjusting nut and washer. S Move the cable clear of the support bracket. S Remove the rear adjusting nut and washer. 
(26)  Move the cable aft through the rubber grommets in the engine cooling baffles.  Move the propeller control cable clear of the engine. 
(27)  Remove the propeller (if necessary).  Refer to Section 61-00. 
(28)  Disconnect the mixture control eye end at the mixture control lever at the fuel injector: S Remove the nut and washer from the long bolt at the mixture lever. S Release the mixture cable eye end from the lever. S Remove the spacer and the long bolt. 
(29)  Remove the eye end from the mixture control cable: S Release the lock-nut. S Remove the eye end fitting and lock-nut from the cable. 
(30)  Release the mixture cable from the support bracket at the front of the engine: S Remove the bottom adjustment nut and washer from the control cable. S Move the control cable clear of the bracket. S Remove the top adjustment nut and washer from the control cable. 
(31)  Move the cable up through the rubber grommets in the engine baffles and clear of the engine. 

71-00-00
Power Plant
AMM

DA 40 Series

Detail Steps/Work Items  Key Items/References 
(32)  Disconnect the throttle control cable at the Injector: S Remove the nut and washer from the attachment bolt. S Remove the eye end from the bolt. S Remove the bolt and washer from the throttle lever at the injector. 
(33)  Remove the eye end from the throttle control cable: S Release the lock nut. S Remove the eye end and the lock-nut. 
(34)  Remove the control cable from the support bracket at the bottom of the engine: S Remove the front adjustment nut and washer from the outer sheath. S Move the control cable clear of the bracket. 
(35)  Move the throttle cable clear of the engine. 
(36)  Disconnect the alternate air control cable: S Release the screw which attaches the wire end to the swivel in the alternate air assembly. S Remove the lock-nut which holds the control cable outer sheath in the support bracket at the alternate air assembly. S Move the control cable clear of the engine mount. 
(37)  Remove the air baffles.  Refer to Section 75-00. 
WARNING: DO NOT GET FUEL ON YOU. FUEL CAN CAUSE SKIN DISEASE. DO NOT ALLOW FIRE NEAR FUEL. FUEL BURNS AND CAN CAUSE INJURY TO PEOPLE AND DAMAGE TO EQUIPMENT. 

71-00-00
AMM

DA 40 Series

Detail Steps/Work Items  Key Items/References 
(38)  Disconnect the fuel feed hose at the firewall.  Use a suitable container to catch the fuel. Put caps on the hose and the firewall connection. 
(39)  Disconnect the fuel feed hose at the outlet from the fuel pump.  Move the hose clear of the engine mount. 
(40)  Disconnect the fuel drain hose from the engine-driven fuel-pump and move the hose clear of the engine. 
(41)  Remove the cable ties that attach the fuel flow divider drain to the engine mount and the ignition harness.  Note the location of the ties! 
(42)  Disconnect the engine breather hose from the accessory housing at the top of the engine.  Put caps on the breather hose and the engine connection. 
WARNING: DO NOT GET OIL ON YOU. OIL CAN CAUSE SKIN DISEASE. 
(43)  Disconnect the oil pipe at the top of the accessory-housing.  Use a suitable container to catch the oil. Put caps on the oil pipe and the accessory-housing connection. 
(44)  Disconnect the oil pipe at the front of the oil cooler.  Use a suitable container to catch the oil. Put caps on the oil pipe and the oil cooler. 
　
中國航空網 m.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：鉆石40飛機維護手冊 DA 40 SERIES AMM 5(4)