曝光臺 注意防騙 網曝天貓店富美金盛家居專營店坑蒙拐騙欺詐消費者

If the A/L ID is not valid, the MCDU scratchpad displays the "ENTER A/L IDENT" message. After having cleared the scratchpad, the crew writes the two-letter A/L ID code in the scratchpad. Pressing the 3L key enters the A/L ID code in the 3L field. The crew should repeat the same operation for the three-letter A/L ID code using.the.4L.key,.instead.of.the.3L.key.
If no VHF Service Providers have been selected, the MCDU scratchpad displays the "ENTER VHF3 SCAN MASK" message. On the VHF3 SCAN MASK page, select a service providers list, in the airline priority order, and activate the VHF SCAN MASK function. An example of the process for the selection of the service providers.SITA.725.and.ARINC.is.as.follows:
.  
Press the 5L key. The star next to the ERASE indication disappears then reappears.

.  
Press the 1L key to select SITA 725. The SELECT indication goes off and the.priority.number.of.selection.E1.comes.into.view.

.  
Press the 1R key to select ARINC. The SELECT indication goes off and the.priority.number.of.selection.E2.comes.into.view.

.  
Press the 5R key to activate the VHF SCAN MASK function. The star next to.the.SCAN.MASK.LOAD.indication.disappears.and.then.reappears.

ATSU.And.CPDLC
FCTM O.I..(30.JUL.04)

9.50.4

A330/A340 COMMS.&.NAV
O.I..(30.JUL.04)
FCTM ATSU.And.CPDLC
Notification
Notification.is.made.through.the.NOTIFICATION.page.as.follows:

The FMGC provides the ATC FLT number. The notification procedure is used by the ATC to correlate the aircraft with the ICAO flight number. Consequently, it is essential to enter exactly the same number, shown on the ICAO flight plan (with the.same.number.of.letters),.on.the.INIT.page.
The ATC CENTRE field defaults to the centre that was connected during the previous.flight..It.can.be.changed,.if.applicable.
Once the ATC centre has been notified, "NOTIFIED" is displayed on the NOTIFICATION page. The ATC centre will then initiate the CPDLC and/or Automatic Dependent Surveillance (ADS) connection. Therefore, re-notifications should.be.avoided.
For ADS operations, check on the CONNECTION STATUS page that the ADS is set.to.ON.prior.to.performing.a.notification.
ATSU.And.CPDLC
FCTM O.I..(30.JUL.04)
Connection
Before.connection,.the.DCDU.screen.appears.as.below:

Once notified, the connection is made at the ATC's discretion. When the connection is established in a CPDLC or CPDLC/ADS environment, the active centre is displayed on the DCDU and the pilot should verify that the appropriate centre.is.connected.

For operations in an ADS only environment (i.e. no CPDLC), "NO ACTIVE ATC" remains displayed on the DCDU and does not reflect the ADS contract status. This is due to the fact that the DCDU is the interface that sustains CPDLC communication, whereas the ADS is an additional feature which is transparent to the.crew.
9.50.6

A330/A340 COMMS.&.NAV
O.I..(30.JUL.04)
FCTM ATSU.And.CPDLC
CONTROLLER/PILOT.DATALINK.COMMUNICATION.(CPDLC)
This section gives only a few typical examples of the messages that are exchanged between the crew and ATC. To avoid ambiguity, the following is recommended:
. Avoid.sending.multiple.clearance.requests.in.the.same.message . Avoid.duplicating.messages..Consequently:
.  Answer.incoming.messages.as.soon.as.possible
.  Do not re-send your message if ATC does not answer immediately. If, after a reasonable period of time, you feel it is necessary to re-send a message, e.g. a clearance request, do not re-send the same.request..Use.a.negotiation.query,.such.as."WHEN.CAN.WE..."
.  
Close messages when they have been answered or sent to keep the screen.free.for.additional.messages

.  
Avoid using free text. If it is necessary to use free text because pre-formatted messages do not allow for a specific message element, use standard.ATC.phraseology
　
中國航空網 m.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：A330/A340 機組訓練手冊 FCTM Flight Crew Training Manual(90)