(a)
Remove the protection caps.
(b)
Lubricate the new gasket (19) with the beeswax.
(c)
Put the new gasket (19) on the boss of the diffuser and combustor case.
(d)
Install the fuel injector (5) in the boss on the diffuser and combustor case.
NOTE: Turn or lift the fuel injector, as it is necessary, to
____ install the fuel injector in the diffuser and combustor case.
1) Align the bolt holes in the support with the bolt holes in the diffuser and combustor case.
(e)
Lubricate the threads of the bolts (21) with engine oil.
(f)
Install the bolts (21) to attach the fuel injector (5) to the diffuser and combustor case. 1) Tighten the bolts (21) to 65-85 pound-inches (7.3-9.6
newton-meters). 2) Tighten the bolts (21) again to 65-85 pound-inches (7.3-9.6 newton-meters) until you keep the necessary torque. 3) Install the lockwire or safety cable and safety cable ferrule to the bolts (21).
(g)
Lubricate the new packing (20) with the petroleum jelly.
(h)
Install the new packing (20) to the groove on each of the three fuel injectors (5).
(i)
Lubricate the new packings (3) with the petroleum jelly.
(j)
Install the new packings (3) on each end of the transfer tube (2).
(k)
Install the transfer tube (2) in the supply tube (1).
(l)
Connect the fuel manifold (4) to the fuel injectors (5).
NOTE: You will tighten the fuel manifold nuts after you do the
____ leak check of the fuel manifold.
1) Lubricate the threads of the fuel injectors (5) with engine oil.
EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú
73-11-05
ALL ú ú N01 Page 480Q ú Oct 10/97
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
////////////////////////A / PW4000 SERIES /747-400 / ENGINES/MAINTENANCE MANUAL ////////////////////////
2) Connect the fuel manifold (4) to the fuel injectors (5). 3) Tighten the fuel manifold nuts (4) with your hand.
(m) Connect the supply tube (1) to the fuel manifold (4).
NOTE: You will tighten the supply tube nut after you do the
____
leak check of the fuel manifold.
1) Lubricate the threads of the fuel manifold inlet (4) with
engine oil. 2) Connect the fuel supply tube (1) to the fuel manifold (4). 3) Tighten the supply tube nut (1) with your hand.
S 794-327-N00
(2) Do this task, which is found at the end of this section: "Fuel Manifolds Leak Check"
NOTE: After you do the leak check of the fuel manifold, you must
____
install all remaining parts you removed.
S 414-292-N00
(3)
ENGINES PRE-PW-SB 72-567; Install the left diffuser-seal air vent-tube (157), if it was removed (Fig. 405).
(a)
Remove the caps from the fitting on the diffuser case and the port on the HPC rear case.
(b)
Install the gasket (167) in the groove in the port on the HPC rear case.
(c)
Install the deflector (166) in the port on the HPC rear case.
1) Align the pin on the deflector (166) with the alignment hole in the HPC rear case.
(d)
Lubricate the threads of the tube nut (155) with the
antigalling compound.
(e)
Attach the new gasket (165) to the flange of the air vent tube (157) with the paraffin wax.
(f)
Put the air vent tube (157) in position on the engine.
EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú
73-11-05
ALL ú ú N01 Page 480R ú Jun 18/01
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
(g)
Connect the tube nut (155) to the fitting on the diffuser case. 1) Tighten the tube nut (155) with your hand.
(h)
Lubricate the threads of the bolts (161, 164) with engine oil.
中國航空網 m.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：747-400 AMM 飛機維護手冊 發動機燃油和控制 1(84)
