NOTE: Turn or lift the fuel injector, as it is necessary, to
____ install the fuel injector in the diffuser and combustor case.
 EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú

 73-11-05
 ALL  ú ú N01 Page 462 ú Jun 18/99
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
(e)  Align the bolt holes in the support with the bolt holes in the
 diffuser and combustor case.
 (f)  Put the bracket (12, 13, or 14) on the fuel injector (5) with
 the bolt holes aligned.
 (g)  Lubricate the threads of the bolts (21) with engine oil.
 (h)  Install the bolts (21) to attach the fuel injector (5) and the
 bracket (12, 13, or 14) to the diffuser and combustor case.
 1) Tighten the bolts to 65-85 pound-inches (7.3-9.6
 newton-meters).
 2) Tighten the bolts (21) again to 65-85 pound-inches (7.3-9.6
 newton-meters) until you keep the necessary torque.
 3) Install the lockwire or safety cable and safety cable
 ferrule to the bolts (21).
 (i)  Lubricate the new packing (20) with the petroleum jelly.
 (j)  Install the packing (20) to the groove on each of the three
 fuel injectors (5).
 (k)  Lubricate the new packing (3) with the petroleum jelly.
 (l)  Install the new packings (3) on each end of the transfer tube
 (2).
 (m)  Install the transfer tube (2) in the supply tube (1).
 (n)  Connect the fuel manifold (4) to the fuel injectors (5).
 NOTE: You will tighten the fuel manifold nuts after you do the____
 leak check of the fuel manifold.
 1) Lubricate the threads of the fuel injectors (5) with engine
 oil.
 2) Connect the fuel manifold (4) to the fuel injectors (5).
 3) Tighten the fuel manifold nuts (4) with your hand.
 (o)  Connect the supply tube (1) to the fuel manifold (4).
 NOTE: You will tighten the supply tube nut after you do the____
 leak check of the fuel manifold.
 1) Lubricate the threads of the fuel manifold inlet (4) with
 engine oil.

 EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú

 73-11-05
 ALL  ú ú N01 Page 463 ú Jun 18/99
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
////////////////////////A / PW4000 SERIES /747-400 / ENGINES/MAINTENANCE MANUAL ////////////////////////
2) 3)  Connect the fuel supply tube (1) to the fuel manifold (4).Tighten the supply tube nut (1) with your hand.
 S 794-312-N00
 (2)  Do this task, which is found at the end of this section: Manifolds Leak Check" "Fuel
 NOTE:____ After you do the leak check of the fuel manifold, you must install all remaining parts you removed.
 S 424-451-N00
 (3)  For the No. 7 fuel injector, attach the support tube (34) for the wire harness with the steps that follow: (a) Attach the support tube (34) to the bracket (14) with the bolt (35) and nut (33). 1) Tighten the nut (33).
 S 424-452-N00
 (4)  For the No. 8 fuel injector, do the steps that follow: (a) Attach the clamp (40) to the bracket (13) with the bolt (42) and nut (41). 1) Tighten the nut (41).
 S 424-453-N00
 (5)  For the No. 9 fuel injector, do the steps that follow: (a) Attach the support (50) to the bracket (12) with the bolt (48), washer (49), and nut (43). 1) Tighten the nut (43). (b) Attach the bracket (46) to the bracket (12) with the bolt (47), washer (45), and nut (44). 1) Tighten the nut (44).
 S 414-188-N00
 (6)  Install the No. 2 turbine-vane cooling-air duct (AMM 75-24-02/401) if it was removed.

 EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú

 73-11-05
 ALL  ú ú N01 Page 464 ú Jun 18/01
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
H. Return the Aircraft to its Usual Condition
　
中國航空網 m.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：747-400 AMM 飛機維護手冊 發動機燃油和控制 1(68)